2022 Ford F-250 Super Duty on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford Fiesta 1.0L EcoBoost sales robust in early going

Okay, okay, okay, so I was just a smidge wrong. Those that read my review of the Ford Fiesta with the new 1.0-liter, EcoBoost engine will know that while I really enjoyed the torquey little three-cylinder, I was concerned that Ford's decision to force 1.0-liter owners into a manual transmission, steel wheels and one trim level might hurt sales of the new engine. I was also concerned that the promised 45-mile-per-gallon highway rating wouldn't be enough to tempt buyers into trying an engine that's so far outside of what the general public is use to. My concerns, though, seem to have been for naught.
While not doing a booming business on the triple-equipped Fiesta, Ford is seeing a take rate of four to eight percent per month in the engine's first few months on sale. Now, four to eight percent might not sound like a lot - if, like last year, the Fiesta sells around 71,000 units, there'd be barely 5,600 1.0-liter models on the road. It is also small potatoes relative to the take rate on EcoBoost-equipped vehicles across the Ford range, which US sales analyst Erich Merkle estimates to be roughly 35 to 40 percent of retail sales. Still, according to The Detroit News, the 1.0-liter is getting adopted at roughly the same rate as the sparkling Fiesta ST, which should be a solid indication of just how well this little engine is doing.
The 1.0-liter's success "really speaks volumes, not just to what we're doing with the Fiesta, but with EcoBoost in general," Merkle told Autoblog.

Exceptionally rare '65 Ford GT40 Roadster prototype up for auction

Think of mid-engined supercars and your mind is bound to gravitate towards Europe, but the United States has been known to make a handful from time to time - exceptional vehicles from the likes of Vector, SSC, Mosler, Hennessey, and Saleen. But long before any of those came around, Ford famously became obsessed with beating Ferrari at its own game, leading to the development of the iconic GT40.
The story is well known, sending Ford to the checkered flag at Le Mans four times in a row in the late 1960s. Ford and Shelby also built over 100 for public consumption, but just four of them were roadsters. Of those only one remains in original condition, and now that exceedingly rare example going up for auction.
Consigned to RM Auctions for its mid-August sale during Pebble Beach weekend in Monterey, California, this 1965 model is the first GT40 Roadster built. It was used as a development and demonstration vehicle for Ford and Shelby. Carroll Shelby himself drove Henry Ford II in this very car during one of many test and demo events, this time held for Ford's board of directors in Los Angeles.