2014 King Ranch Crew 4x4 Fx4 Navigation Sunroof Leather Heated V8 Diesel on 2040-cars

Auto blog

Ford to spread all-wheel drive across performance range

Car and Driver took a closer look at the all-wheel-drive system in the Focus RS, Ford reps having made "broad hints" about it being applied to other performance vehicles. One spokesperson even said that he "can see this as one of those technologies of the future." That would make sense because, as C/D notes, it couldn't have been an inexpensive job to engineer the torque-vectoring unit for the Focus – one that can send 70 percent of torque to the rear wheels, and send 100 percent of that portion to either wheel if needed. C/D also clues into the system's close similarity to the AWD unit in the recently updated Range Rover Evoque, which is manufactured by Sweden's GKN Driveline. In the Evoque, torque vectoring is brake based and two electronically controlled clutches turn the Range into a front-wheel-drive crossover under 22 miles per hour. Ford wouldn't comment on the GKN Driveline connection, or even if there is one. No matter where it might come from, more performance Fords are good for every enthusiast, and we do not look an AWD, torque-vectoring gift horse in the mouth. Featured Gallery 2016 Ford Focus RS News Source: Car and Driver Ford Technology Hatchback Performance

2015 Ford Mustang to offer solid-rear axle, sort of

One of the biggest knocks against the last Ford Mustang was its solid-rear axle. Not one to actively court criticism, Ford dutifully swapped out the old-fashioned rear end for something a bit more modern in the redesigned 2015 Mustang, adding an independent rear suspension across the board.
While an IRS Mustang is great news for those that value handling and ride comfort, there's one big group that it's bad news for - drag racers. See, a solid-rear axle is a big deal for drag racers, because not only is it more durable and cheaper, but it's better for the hard launches that can make or break a race.
To satiate this vocal demographic, Ford will sell a body-in-white version of the Stang, complete with a nine-inch rear axle, that will debut at the 2014 Performance Racing Industry show. The news came from gas2.org, which cited an unnamed employee of Ford Racing at this year's PRI show.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).