Ford F-150 Lariat Supercrew Auto Power Heated Leather Microsoft Sync Keyless on 2040-cars

Auto blog

Ford confirms 1.5-liter EcoBoost four-cylinder engine for 2014 Fusion

Earlier this week, reports were swirling 'round the internet about the 2014 Ford Fusion getting a new 1.5-liter three-cylinder EcoBoost engine. That was... half correct. Ford today confirmed that the 2014 Fusion is, in fact, getting a new 1.5-liter EcoBoost mill, but it has four cylinders, not three.
The new 1.5-liter engine will be the fifth EcoBoost powerplant from Ford Motor Company. Initially to be built at the automaker's Craiova, Romania plant, it will also be offered in the Fusion's twin, the Mondeo, in other markets. This engine will debut at the Shanghai Motor Show next month, and the 1.5-liter is of particular importance in the Chinese market - there is significant tax relief in the People's Republic for vehicles powered by engines with a capacity of 1.5 liters or less.
At a media briefing Thursday, Ford declined to divulge exact power or fuel economy numbers, though Joe Bakaj, vice president of powertrain engineering, told Autoblog that power output should be similar to that of the current 1.6-liter inline-four, and that overall efficiency will be "better than the 1.6." Our earlier report stated that the 1.5-liter four will produce 177 horsepower and 177 pound-feet of torque - losses of 1 hp and 7 lb-ft versus the 1.6-liter engine. Ford states that the 1.5-liter four will feature many of the same technologies used on the company's 1.0-liter EcoBoost inline-three, including an integrated exhaust manifold that recaptures much of the engine's heat.

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.

Ford F-150 could be affected by tornado-damaged supplier in S.C.

The disruption caused by a tornado that severely damaged a South Carolina auto-parts plant and killed a contract security guard last week could be felt by more automakers than just Ford and affect more than just its best-selling F-Series pickup, which is due for an update. And there’s still no estimate for when operations might resume at the plant. The Detroit Free Press reports that the BorgWarner plant in Seneca, near Greenville, makes transfer cases for F-150 and Super Duty pickups, the Ford Explorer and Expedition, Transit cargo vans, and Lincoln Navigator and Aviator SUVs. ItÂ’s also a supplier for the Ram 1500 and Toyota Tundra trucks. Transfer cases shift power from the transmission to the front and rear axles in four-wheel-drive vehicles. BorgWarner says it still has no update for when it might partially or fully resume operations. The tornado that ripped through the area in the western part of the state on April 13 tore the roof, walls and signage off the factory and killed a 77-year-old contract worker when the security building he was sheltering in collapsed. Only four or five others were inside the plant, which has been idled because of the coronavirus outbreak, when the tornado struck. In an SEC filing on Friday, Ford said it has sent employees to the site to help BorgWarner and assess the damage to FordÂ’s tooling. “Initial assessments indicate that the Ford tooling was not materially damaged in this incident,” Ford said in the filing. “We do not have sufficient information to estimate when the facility will be back on-line or whether or the extent to which this incident will impact our plans to resume production of four-wheel drive and all-wheel drive vehicles.” A Fiat Chrysler spokeswoman also told the Freep the company was working with BorgWarner on recovery plans. A Toyota spokesman told Autoblog that "we are collaborating with BorgWarner to help restore production for transfer cases for Tundra assembly. We are confident that theyÂ’ll fully recover over time." Like other automakers, Ford shut down production at its U.S. plants last month as a precaution against the coronavirus pandemic. But Ford hasnÂ’t yet said when it plans to reopen its factories. FCA is targeting May 4 to resume production. Models like the F-150 and Lincoln Navigator are major sources of profit for Ford, which estimated it lost $2 billion in the first quarter.