F150 Lariat 2008 4wd White Ext./tan Int. Low Miles - Mint - Must See on 2040-cars

Auto blog

Why Edmunds took a sledgehammer to its 2015 Ford F-150

The discussion around repair bills for the aluminum-bodied 2015 Ford F-150 pickup continued from the beginning of last year to the end, and haven't abated; as an aside, some Tesla Model S owners have been shocked at disquieting repair estimates for minor damage to their aluminum wunder-sedans. Edmunds decided to inject some fact into the fray: it bought a $52,000 long-term 2015 F-150 and clouted it with an eight-pound sledgehammer. Twice. The rear of the bedside took the impacts since it couldn't be replaced, it would have to be repaired. To the pickup's credit, the only reason associate editor Travis Langness hit it twice was that the first sledgehammer blow didn't do as much damage as Edmunds wanted. After the second, the visible damage included the two direct impacts, a few creases, and a cracked taillight, so they drove the pickup to Santa Monica Ford to get an estimate, complete with a fictitious story about how the damage occurred and the mercy plea that Langness was paying for the repair out-of-pocket. In Part 2 Langness hits on some of the details with getting the truck fixed, such as the massively expensive taillight and the list of tools Ford recommends dealers have to work on aluminum. But he was promised he'd have his truck back in seven days, and Santa Monica Ford got it back to him in seven days. In Part 3 we get the bill. It's not small, but it's quite a bit less than it could have been if the service manager had charged Edmunds the official labor rate for aluminum. We're not going to spoil it here, so check out the videos above and below for the beginning and the end, and head over to Edmunds for the complete story about how it all happened and some riffing on the repair numbers. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Related Video:

Ford announces first non-pursuit-rated police car ever

Ford announced its first non-pursuit-rated Police Interceptor ever, based on the Taurus, which employs the smaller 2.0-liter EcoBoost four-cylinder engine in place of similar pursuit-rated Police Interceptors powered by naturally aspirated 3.5-liter and 3.7-liter V6s and the top-spec 3.5-liter EcoBoost V6. Officially called the Special Service Police sedan, the car was commissioned at the request of law-enforcement agencies that desire a more fuel-efficient vehicle for detectives, administrators and campus police, who don't necessarily need pursuit-rated vehicles.
The 2.0-liter EcoBoost engine produces 240 horsepower and 270 pound-feet of torque, but more importantly, it allows the SSP sedan to achieve somewhere in the neighborhood of 22 miles per gallon city and 32 mpg highway, which are the civilian 2.0-liter Taurus' official EPA ratings. Ford estimates that the SSP sedan will get 20 mpg city, 30 mpg highway and 23 mpg combined, with the help of Active Grille Shutters that open to allow more cooling air through to the radiator, or close to optimize aerodynamics and fuel economy. Those numbers compare favorably to the discontinued Crown Victoria-based Interceptor's 14 mpg city and 21 mpg highway and the newer Taurus-based cars equipped with V6s, the most fuel efficient of which gets 18 mpg city and 26 mpg highway.
If it was driven 90,000 miles over the course of three years, a 2.0-liter SSP sedan would save law enforcement agencies $5,042.92 versus the Crown Vic, Ford estimates. The EPA is expected to post official fuel-economy numbers for the SSP sedan in December. Until then, read the press release below for more information.

Ring Brothers shows 1965-66 Mustang fastback carbon fiber body

We covered one of Ring Brothers' more extreme SEMA builds yesterday, the De Tomaso Pantera-based ADRNLN, but if that well-executed but over-the-top Italian-American exotic is too much for you, then perhaps this Ring Brothers 1965 Ford Mustang fastback with a carbon-fiber body suits your tastes better.
What the performance-parts manufacturer is showcasing with the Mustang is the carbon-fiber body itself, which is fashioned around the 1965-66 fastback. It can be bought from the company and bonded to the skin and unibody as a do-it-yourself project, or you can take your Mustang to Ring Brothers and have the body installed there. The fenders, doors and quarter panels are two-inches wider than stock, and Ring Brothers offers a custom widebody chassis to those who want the complete package.
The show car looks sharp in person lowered on HRE wheels, and we appreciate the bare front end so we can see the supercharged V8 and front coilover suspension, though the details on those performance upgrades are slim. Also note the custom independent rear suspension setup at the rear.