Clean on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

3dCarbon now offering body kit for Ford Fusion

A factory-backed body kit by 3dCarbon is now available to Ford Fusion owners who want their car to stand out from the crowd while not being too flashy. The body kit adds a more aggressive front spoiler, side skirts, rear body trim and spoiler that are, in fact, integrated quite nicely into the Fusion's already-comely styling, just as 3dCarbon claims. All Fusions with the kit also receive dual exhaust ports with the stainless-steel exhaust surrounds usually reserved for the Titanium package Fusion EcoBoost models.
A nice detail of 3dCarbon's injection-molded urethane body kit is that it has undergone crash testing to certify that it can withstand crashes up to five miles per hour. Because of this, the kit is warrantied by 3dCarbon for five years or 50,000 miles, much like Ford's warranty on its own parts. In fact, the kit is available through participating Ford dealers and can be financed through Ford Motor Credit. Buyers can purchase the kit - pre-painted or unpainted - and install it themselves, or it can be purchased with a new Ford Fusion and installed at the dealer, pre-painted to factory specifications. Of course, it can also be ordered directly from the source. Take a look at the press release below for more detailed information on the body kit, and let us know what you think of it in Comments.

2020 Ford Explorer, Lincoln Aviator reportedly facing numerous QC issues

A lengthy report in the Detroit Free Press delves into a range of quality control issues confronting the 2020 Ford Explorer and its luxury platform sibling, the 2020 Lincoln Aviator. Freep says it's been following the issue for two months, tapping various unnamed sources for information on the automaker's unorthodox route to resolution. Seems the problem is Explorers and Aviators leaving the production line at the Chicago Assembly Plant with flaws in areas like the chassis, transmission and suspension, said vehicles trucked to Ford's Flat Rock Assembly Plant (FRAP) outside of Detroit for repair. The estimates range from 10,000 to 18,000 vehicles affected, numbers so high that Ford has sought help from Roush Engineering in nearby Allen Park, and brought workers and managers from other plants in the Midwest to FRAP to get vehicles repaired and shipped to dealers. Ford hasn't shared the nature of the problems with anyone outside the company, including dealers and customers. Freep's sources are said to include workers who have provided photos of certain vehicles and of tents used to house parts at the FRAP repair site. The Explorer chassis allegedly has an unidentified problem that engineers are using X-rays to diagnose, and the transmission is having problems sensing when it's in park or going into park. Both the Explorer and Aviator have come off the line with HVAC units that only blow hot air. And the Aviator's height-adjustable suspension enters failure mode for unknown reasons. These come on top of quotidian mishaps common to every new vehicle, but that are meant to be sorted in pre-production, like missing emblems and trim pieces. They also come on top of a recall in early August issued for the Explorer and Aviator concerning the instrument cluster and parking brake, and another at the end of August over rear seatbacks that could collapse in a crash. An automaker spokesperson told Freep, "Making updates to preproduction models based on all-new platforms as they roll off the assembly line – is standard industry practice." Except these aren't pre-production, these are early production vehicles that paying customers and dealers are waiting for, and some of the affected vehicles have been pulled off dealer lots. Dealers say they are fine waiting for the trucks to get sorted out, and they'd rather have Ford fix the problems before the SUVs go to customers.