2014 Ford F150 Xlt on 2040-cars

Auto blog

2014 Ford Transit unveiled in Chassis Cab and Cutaway versions

As a leader in commercial vehicles here in the US, we knew Ford wouldn't take too long to show off the chassis cab and cutaway versions of its 2014 Ford Transit van. Set to go on sale this fall, Ford already revealed the full-body version of the Transit, and now it has pulled the cover off exposed-frame models just in time to to compete against the all-new Ram Promaster.
The term "chassis cab" refers to models with a fully enclosed cabin used for box vans or rental trucks, while cutaway models leave the cabin open behind the B-pillars for a pass-through on vehicles such as Class C motorhomes or ambulances. Both will offer three wheelbase options (138, 156 and 178 inches), the choice of single or dually rear axles, and plenty of upfitter-friendly touches including a pre-wired body harness and multiple body mount locations.
The new design will also help make upfitting a little easier since the fuel filler is now built into the cab (just behind the driver's door). Those integrated fuel filler necks will serve to feed either a 3.7-liter V6, a 3.5-liter EcoBoost V6, or a 3.2-liter Power Stroke diesel. Transit chassis cab and cutaways will wear varying Gross vehicle weight ratings from 9,000 pounds to 10,360 pounds depending on spec.

After Years Of Delays, Rear Visibility Requirements Move Closer To Reality

Regulations that would require automakers to improve rear-view visibility on all new cars and light trucks are nearing completion after six years of delays. The U.S. Department of Transportation sent its proposed rear-visibility rules to the Obama administration for review on Christmas Day. The White House Office of Management and Budget now must finalize the regulations. The rule are intended to minimize the risk of pedestrian deaths from vehicles in reverse, a type of accident that disproportionately affects children. Already in 2014, two children have died from cars backing over them, driven in each case by the children's father. Specifics of the Transportation Department's proposal are not available during the review, but the rules are expected to compel automakers to install rear-view cameras as mandatory equipment on all new vehicles. That's what safety advocates have wanted all along. Thought they were pleased the proposed ruling had finally been issued, there was some worry Friday the final rules would omit the rear-view camera mandate. "We're encouraged, but we're also a little concerned about speculation the rear-view camera may not be in there," said Janette Fennell, the president and founder of Kids and Cars, a nonprofit organization dedicated to protecting children in and around vehicles. "I'm wondering where that might be coming from." On Thursday, The Automotive News had reported the possibility the new standards could offer an alternative to rear-view cameras, such as redesigned mirrors, that improved visibility. The Office of Management and Budget typically completes its reviews of new rules in 90 days, although that can be extended. OMB officials said Friday they do not comment on pending rules. The intent of the rules is to enhance rear visibility for drivers and prevent pedestrian deaths. Approximately 200 pedestrians are backed over in the United States each year, according to estimates from the National Highway Traffic Safety Administration. Accidents Mostly Affect Children Roughly half the victims are children younger than age five. A government analysis concluded approximately half the victims -– 95 to 112 -– could be saved with new regulations. Yet the rules have arrived at a glacial pace. President George W. Bush signed legislation that had been passed with bipartisan Congressional support in 2008. But automakers have fought the idea of adding rear-view cameras, saying it is too expensive.

Plug In 2014: ALTe ready to join Ford's EQVM to convert, sell F-150 PHEV [w/video]

It's been a while since we've checked in with ALTe and its plans to convert big work vehicles like the Ford F-150 into plug-in hybrids. So, when we saw a demonstration vehicle sitting outside the San Jose Convention Center at the Plug In 2014 Conference last week, we had to get a closer look. When we did, we realized that it's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. It's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. The reason for the well-worn F-150 with 30,000 miles on it is that ALTe has been showing off its extended-range EV technology to lots of people all around the country, and Kyle Maki has been the man on the scene more often than not. "This one, I've taken all over the country," he told AutoblogGreen. "I've wore out that seat, I think. The only reason this one wasn't driven here was because we were in Charlotte [NC] last week and I didn't want to take a chance and not make it in time for this event." In other words, ALTe is out there, ginning up excitement for the idea of a plug-in hybrid Ford with an electric range of up to 40 miles and which can then continue on gas for another 360 miles at around about 25 miles per gallon. ALTe wants to not only convert new vehicles but it also offers retrofits for fleets that are happy with their current fleet. The company offers converted versions of the Ford E350 and E450 utility vehicles now but the near-mythical F-150 PHEV is still "coming soon." Yes, orders are now being accepted, but you will be forgiven if you think this is all happening on a slow time scale. There are simply a lot of things to do before ALTe can sell the truck. ALTe is currently attempting to join Ford's EQVM program, which is the electric version of the standard Qualified Vehicle Modifiers program. The QVM program requires coachbuilders to "be successfully evaluated by Ford Motor Company on criteria such as engineering, the manufacturing process, quality control, and adherence to Ford and Lincoln Divisions guidelines." Qualified applicants must also meet all applicable Federal Motor Vehicle Safety Standards, conform to Ford/Lincoln conversion guidelines and agree to be inspected annually as well as have a "commitment to continuous improvement." Maki has a simpler explanation. "It basically means you're a preferred supplier, a Tier 1, if you will," he said.