2010 Ford Svt Raptor on 2040-cars

Auto blog

2017 Ford F-150 Raptor desert testing heats up

In case there was any doubt, Ford is taking the development of the second-generation SVT Raptor very, very seriously. The Blue Oval recently completed over 1,000 miles of testing in the boiling heat of the American southwest. Apparently, that mileage was accrued over a 66-mile route designed to mimic the torturous terrain encountered by racers in the Baja 1,000 off-road race. The prototypes, which were built from a mix of existing and next-gen Raptor components, were tested with "fast sandy washes, deep-rutted silt beds, steep climbs in deep sand, and slow meticulous crawls through tight trenches." Ford claims the new truck managed to run the circuit 25-percent faster than the current F-150 SVT Raptor, averaging 50 miles per hour while going as fast as 100 mph in stretches. That said, Dearborn didn't release any dedicated times, so it's unclear just how quickly the 66-mile stage was completed. We do know that durability was a big part of the testing. Ford claims each lap was completed by what sounds like a pretty significant jump, with the trucks ascending a steep ramp onto a two-foot plateau and then completing a step-down to level ground. We have to take Ford at its word here, though. "Steep" can mean any number of things, and we've no idea just how fast the trucks were hitting the ramp or how much air they got. Hopefully, the jumps were aggressive enough to prevent future frame issues. Still, Ford boasting about how rough the Raptor's testing is can be taken as a positive sign for fans of the next-generation of SVT's rugged pickup. NEW F-150 RAPTOR WRAPS UP INITIAL DESERT DURABILITY TESTING DEARBORN, Mich., July 7, 2015 – The 2017 F-150 Raptor – Ford's toughest, smartest, most capable off-road truck ever – recently completed more than 1,000 miles of testing in the southwestern United States. Over 1,028 miles of desert trail designed to parallel the Baja race course in Mexico, the 66-mile route featured a wide range of surfaces including fast sandy washes, deep-rutted silt beds, steep climbs in deep sand, and slow meticulous crawls through tight trenches. The truck topped speeds of 100 mph in places, slowing to 10 mph in others, for an average speed of approximately 50 mph. The 2017 Raptor is 25 percent faster than the current truck based on lap times. At the end of each lap, the new Raptor completed a tabletop jump consisting of a steep ramp up to a two-foot plateau, then a step-off back to level ground.

Ford, Alcoa announce next generation of aluminum lightweighting for F-150

Ford likes what it has seen with the use of aluminum in its world-beating F-150 pickup trucks. Now, the Blue Oval is working with Alcoa to use that company's Micromill material to increase the amount of aluminum in Ford vehicles. In fact, Ford will start using Micromill on 2016 model-year F-150s later this year, and will double the material's use in 2017. The purpose, as you might suspect, is light weighting, which allows Ford to boost towing capacity while adding as little weight as possible. Ford will be the first automaker to use Micromill, and will use it in both structural components and exterior panels. Micromill's rolling-mill system cuts the time it takes to turn molten metal into coil to 20 minutes from about 20 days. Already, Ford has had positive results by using aluminum on its leading pickup truck model. In April, it was announced that the 2015 Ford F-150 achieved a five-star Overall Vehicle Score in the National Highway Traffic Safety Administration's testing. Safety features like inflatable seat belts, adaptive steering columns and a forward collision warning system helped matters. General Motors may have taken note of those results, even after running an ad campaign touting its continued use of steel over aluminum. Last month, GM said it would sink $877 million into its Flint, MI, truck factory. Reuters said much of the expense was to convert many of the bodies for models like the Chevrolet Silverado and GMC Sierra pickups into aluminum. You can take a look at Ford's press release below. Ford Motor Company and Alcoa Inc. are collaborating to produce next-generation automotive aluminum alloys that are more formable and design-friendly. Ford will use Alcoa's Micromill® material in multiple components on the 2016 F-150 – becoming the first automaker to use the advanced automotive aluminum commercially. The companies entered into a joint development agreement to collaborate on next-generation aluminum alloys for automotive parts using Micromill™ technology. ''Light-weighting enables us to design vehicles with great customer attributes – like the F-150, which can tow more, haul more, accelerate quicker and stop faster than the previous F-150, and is more fuel-efficient than ever," said Raj Nair, Ford group vice president and chief technical officer, Global Product Development.

Automakers donating money, vehicles and supplies to Oklahoma tornado relief effort

Judging by the destruction the Oklahoma City area experienced earlier this week, residents are going to need a lot of help in coming months. Fortunately, a number of automakers - including General Motors, Ford, Chrysler, Volkswagen, Honda and Toyota - have stepped up to donate money, supplies and vehicles to aid in the recovery and rebuilding processes.
Here's a quick rundown of which automakers have pitched in and what each contributed so far:
Ford Motor Company has donating $250,000 and a Transit Connect to the American Red Cross, and it will match all other donations made to the Red Cross (up to $250,000) using a special URL tied to the latter's website (link here). Additionally, its local Oklahoma dealers have thrown in an extra $150,000 for the United Way and the automaker will be offering an extra $500 toward the purchase of a new Ford vehicle.