2006 Ford F150 on 2040-cars

Auto blog

Ford recalls 382k vehicles across six campaigns

Ford needs to repair a total of 381,633 vehicles in North America across six newly announced campaigns, including five safety recalls and one compliance recall. By far the largest of these campaigns covers the 342,271 examples of the 1998-2003 Windstar to double check an earlier recall repair. Among these, 283,413 are in the US and 58,858 are in Canada. The combination of corrosion and stress can cause cracks in the rear axle and eventually lead to the part to snap completely. The company reports a small number of accidents might be connected to this, but there are no injuries. The minivans were recalled for this issue back in 2010, and it was investigated by NHTSA. According to Ford's latest announcement, the reinforcement brackets on some of these models might not have been installed correctly. This time, dealers will perform an inspection. Minivans with incorrectly installed brackets will get a new rear axle. The rest of the owners will be offered a deal to replace the part at a reduced cost. The next largest campaign covers 36,857 examples of the 2015 F-150 to fix a problem with the adaptive cruise control. Specifically, there are 33,481 affected trucks in the US, and 3,376 in Canada. According to Ford, "when passing a large, highly reflective truck" the radar in the system can misidentify a semi as being in the same lane as the pickup. The collision warning system would then activate, slowing the F-150. There's one report of an accident with this happening but no injuries. The fix is simply an update to the adaptive cruise control module software. Ford also has a recall for 1,477 examples of its 2016 F-53 and F-59 stripped chassis models, and they're all located in the US. A manufacturing issue might allow the trucks to shift into reverse without the driver first applying the brakes. There are no reports of any accidents from this, though. To repair the problem, the models get a new transmission shift control bracket and an adjustment to the shift cable. The Blue Oval's safety compliance recall covers 708 examples of the 2016 Fusion and Lincoln MKZ, including 658 of them in the US, 28 in Canada, and 22 in Mexico. On these models, a manufacturing problem with the fuel tank could allow it to crack in a crash, which isn't allowed under federal rules. There are no reports of accidents, injuries or fires. The fix will be a new fuel tank for all of them. The company is also repairing 251 units of the 2015 Taurus and Lincoln MKS, plus the 2016 Explorer.

Ford Fiesta ST customs get wild at SEMA

The massive 57-car SEMA showcase by Ford ranges from obvious aftermarket-friendly models like the Mustang, to the not so obvious ones, like the Transit Connect and cute-as-an-explosive-button Fiesta ST. Ford plucked several Fiesta STs for SEMA duty, and we were on the show floor today to get a closer look at some of them.
First up is the striking COBB Tuning and Tanner Foust Racing Fiesta ST (above) finished in a black-and-gray digital camouflage, much like that used in the military, and is meant to raise awareness for the Pat Tillman Foundation. COBB also fitted a three-inch exhaust and a cold-air intake. A new shift knob, carbon-fiber hood and a Kicker stereo round out the mix of upgrades.
MRT got its hands on a Fiesta ST and created a car inspired by Forza Motorsport 5 (below, left). Featuring a two-tone paint job and more performance upgrades than you can shake a stick at, this Fiesta ST is one of the cooler compacts at Ford's stand. A high-performance exhaust system, along with a complimentary COBB induction system, allows the ST to breathe better, while an H&R coil over suspension and Steeda brakes help it stop and turn better than stock.

Hot-selling Ford Expedition, Lincoln Navigator get production boost

Ford is investing an additional $25 million in its Kentucky Truck Plant in Louisville to increase by 25 percent production of the hot-selling and all-new Lincoln Navigator and Ford Expedition SUVs. The investment adds to $900 million in previously announced spending at the plant, which also builds F-Series Super-Duty pickups and employs 8,400 workers. Assembly-line workers are putting in overtime and working voluntary weekend shifts to keep up with demand. The new investment will cover upgrades to the assembly line but does not involve further hiring, Ford spokeswoman Kelli Felker says. The popularity of the Ford Expedition and Lincoln Navigator is a bright spot as Ford stock has been battered by Wall Street amid concerns concerns about the automaker's future vision and slowness to detect trends. Ford says the investment is an example of its bid to improve "operational fitness," one of CEO Jim Hackett's common refrains. Ford says Navigator retail sales more than doubled in January, and Navigators are spending an average of just seven days on Lincoln dealership lots as customers trade in vehicles including Land Rovers and Mercedes-Benz. Nearly 85 percent of buyers are opting for high-end Black Label and Reserve trim packages, contributing to an average transaction price increase of more than $21,000 in January compared to a year ago. The 2018 Navigator won the North American Truck of the Year award and also topped a Detroit News poll of public favorites at last month's Detroit Auto Show. Sales of the Expedition, meanwhile, were up almost 57 percent last month as the full-size SUVs also spent an average of just a week on dealer lots. Platinum trim models represented 29 percent of sales, pushing transaction price increases up $7,800. Ford gave the 2018 Expedition an all-aluminum body to save mass in its first significant redesign since 2007. The plant last year got nearly 400 new robots, mainly in the body shop, to help increase line speed, and Ford added a robot lab where employees can test software tweaks or troubleshoot issues away from the factory floor. The Louisville plant also benefits from extensive new data analytics, with seven big-screen monitors providing minute-by-minute updates showing progress against hourly targets or alerting workers to pending parts shortages. A huge spare-parts "vending machine" lets workers more quickly locate needed parts and keep inventory at necessary levels.