1998 Ford F150 Xlt Xtra Cab,4x4,v8,automatic,cold A/c,clean,$99.00 No Reserve on 2040-cars

Auto blog

Ford, Samsung shack up to bring regen braking to non-hybrid models [w/video]

Ford must be desperate to get itself ready for the beach this summer because it is really trying to get into shape. Shortly after unveiling the Lightweight Concept that cut the weight of a Fusion down to that of a Fiesta, it's now the rest of the line's turn for improvement. The company is wrapping up a 10-year research project aimed at developing next-gen automotive batteries to improve efficiency.
Ford claims that 70 percent of its lineup will have stop/start tech by 2017. The key to this massive proliferation is its new dual-battery system that combines a lithium-ion battery with a lead-acid one and regenerative braking. The setup works by harvesting braking energy and converting it to electricity. When the vehicle stops, the engine shuts off, but the Li-ion battery has enough juice to keep the accessories running. The engine starts up again as drivers take their foot off the brake. The layout would mean less wasted gas while idling. It's already available on Ford hybrids and is somewhat similar to the i-Eloop capacitor-based system from Mazda.
The bigger challenge is tuning the regenerative braking right. While hybrid drivers may be a little more adventurous, when it comes to getting a hang of regen braking, conventional buyers might not be so open-minded. The systems have a tendency to be a little grabby at first and then taper off at very low speeds. Ford needs to make sure it's just right to avoid turning off buyers.

Ford recalling nearly 700k Escape CUVs, C-Max hybrids over two separate safety issues

Poor Escape. Ever since its launch in 2012, Ford's small CUV has been the subject of many, many, many recalls. And today, The Detroit News is reporting that Ford is adding two more recalls to the 2013-14 model year Escape's permanent record, one of them also involves the C-Max hybrid hatchback.
The first recall, covering 692,500 Escape and C-Max vehicles, is due to a software glitch that could cause the airbags - specifically, the safety canopy - to not deploy in a timely fashion during rollover crashes. According to the News, Ford says no crashes or injuries have been reported in relation to this problem.
The second recall, covering 692,700 Escapes, is related to the door handles. The News reports that the exterior door handles could open while the vehicle is in motion, and could also fail to latch properly. Once again, no crashes or injuries have occurred because of this. The National Highway Safety Traffic Administration has not issued an official notice on either recall as of this writing.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: