1993 Ford F150 Xlt on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Consumer Reports criticizes small turbo engines for misleading performance, fuel economy claims [w/video]

Consumer Reports has taken aim at at small-displacement, forced-induction engines, saying the powerplants don't manage to deliver on automaker fuel economy claims. Manufacturers have long held that smaller, turbocharged engines pack all power of their larger displacement cousins with significantly better fuel economy, but the research organization says that despite scoring high EPA economy numbers, the engines are no better than conventional drivetrains in both categories. Jake Fisher, director of automotive testing for Consumer Reports, says the forced induction options "are often slower and less fuel efficient than larger four and six-cylinder engines."
Specifically, CR calls out the new Ford Fusion equipped with the automaker's Ecoboost 1.6-liter four-cylinder engine. The institute's researchers found the engine, which is a $795 option over the base 2.5-liter four-cylinder, fails to match competitors in acceleration and served up 25 miles per gallon in testing, putting the sedan dead last among other midsize options.
The Chevrolet Cruze, Hyundai Sonata Turbo and Ford Escape 2.0T all got dinged for the same troubles, though Consumer Reports has found the turbo 2.0-liter four-cylinder in the BMW 328i does deliver on its promises. You can check out the full press release below. You can also read the full study on the Consumer Reports site, or scroll down for a short video recap.

Formula Drift kicks off 11th season on Streets of Long Beach

The 2014 Formula Drift series kicked off last weekend in Long Beach, and saw Chris Forsberg, who you'll recall went mad and drifted around a warehouse in an Infiniti M, take the title behind the wheel of his Hankook Tire Nissan 370Z (shown above).
Forsberg really ran away with the first round of competition, outscoring his closest opponent, second-place finisher Kenneth Moen and his Bridges Racing Nissan 240SX, by 20 points. Third place was 2013 championship winner Michael Essa and his Yokohama BMW M3, 30.5 points behind Forsberg.
In the manufacturers' title, Nissan took an early lead with 122 points, which isn't a huge surprise considering five of the top ten drifters were piloting either a Z or a product of the brand's S platform. Ford, which had two drivers (Justin Pawlak and Vaughn Gittin, Jr.) in the top ten, took home second place, while BMW is currently third in the manufacturers' standings.