1967 Ford F-100 Custom Cab on 2040-cars

Auto blog

Ford issues six recalls covering 101,000 vehicles for multiple issues

Ford is announcing six separate recalls for a variety of issues affecting a dozen models and a total of 100,610 vehicles in North America. However, according to Ford spokesperson Kelli Felker, "None of them have caused accidents or injuries." Half of them cover fewer than 1,000 cars.
The largest recall covers 92,022 North American examples (about 83,250 in the US) of some models of the Ford Taurus, Lincoln MKS, Ford Interceptor, Flex and Lincoln MKT from the 2013 and 2014 model years; the 2012-2014 Edge and the 2014 Lincoln MKX. All of them have a potential issue with the halfshaft on the right side that might not be fully seated and could move outward over time. If it shifts too far, the models may no longer be able to drive, and the condition could also allow the vehicles to roll away, even when in Park. Dealers will inspect the shaft to make sure it's seated and will replace the part if necessary.
The next-largest recall covers 5,264 North American examples (4,867 in the US) of the Ford F59 Commercial Stripped Chassis from the 2011-2014 model years. It's possible that an electrical junction box can corrode in areas with salty roads and short circuit. The problem could potentially cause a fire. Dealers will replace the box with an improved design.

Second-tier UAW workers promoted for first time after Ford hits quota

The United Auto Workers put out a statement on Friday that 55 Ford workers chosen by seniority would be moved from the Tier 2, entry-level pay rate of around $19 per hour to the Tier 1, non-entry-level rate of about $28 per hour. One of the stipulations in the 2011 UAW-Ford agreement was that only 20-percent of the total hourly workforce could be paid the Tier 2 wages agreed upon in 2007; after that, those workers had to be moved to Tier 1. Even so, the new Tier 1 status makes them less expensive to Ford than veteran Tier 1 workers because they receive fewer benefits. However, Automotive News had reported that same day that Ford was 69 workers shy of the limit, and when AN asked Ford about the situation Ford said it had "some room" on the entry-level roster. If workers do move to the higher pay grade, it will be the first time that's happened since the two-tier system was agreed. But it sounds like there's going to be some haggling between the UAW and Ford before that happens. Ford is the only one of the Detroit 3 automakers to have to work with a cap, since it didn't go through bankruptcy proceedings during The Great Recession; General Motors and Chrysler jettisoned the cap in 2009. GM is said to have 16 percent of its hourly workers at Tier 2 while Chrysler has 42 percent, but Fiat-Chrysler CEO Sergio Marchionne has long been opposed to the two-wage system. The UAW is preparing for its 2015 negotiations with the US automakers. It wants to eliminate the difference in pay by going to the higher scale, if there is a consensus among automakers it seems to be that they also want a single wage, but less than the higher scale, with the addition of profit-based bonuses. The recent statement from the labor union is below. UAW President Dennis Williams and UAW-Ford Vice President Jimmy Settles announced today that the union is delivering on its promise to convert workers DETROIT, Jan. 30, 2015 /PRNewswire/ -- UAW President Dennis Williams and UAW-Ford Vice President Jimmy Settles announced today that the union is delivering on its promise to convert workers making entry-level wages to traditional employees. "The 2011 UAW-Ford agreement allows for a contractual limit of entry-level employees. Once that threshold is surpassed, entry-level employees convert by seniority to 'regular, non-entry level employment.' At this time, fifty-five UAW-Ford workers will receive the wage increases, which put them in the category of non entry-level employment.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.