1958 Ford Panel, 350 Chevy, Auto, Nice Body, New Seat, New Paint on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

'84 MotorWeek Cherokee, Bronco and Blazer comparison indulges your SUV nostalgia

These days, truck-based, full-frame SUVs are somewhat of a rarity on the auto landscape due to the rapid rise in popularity of easier-driving, car-based crossovers. Although, without the gradually building popularity of these chunky, high-riding vehicles decades ago, it's unlikely that America's roads would be filled with so many CUVs today. In its latest dig into the archives, MotorWeek has found a 1984 comparison test of a trio of these early Sport Utility Wagons, as long-time host John Davis called them, that helped get acceptance of this segment going. This is a red, white and blue test of the SUVs from American automakers at the time and pits the Chevrolet Blazer, Ford Bronco and Jeep Cherokee (specifically in Wagoneer guise) against each other. Driving manners and interior usability are considered in the evaluation, but Motorweek actually takes these vehicles off road, too. Among the bigger revelations is the improvement in on-road ability in the past 30 years. While specific 0-60 times aren't given, all three models take around 10 seconds just to get to around 50 miles per hour in the 500-feet on-ramp acceleration test. Check out this clip to see just how far this segment has progressed in the past three decades or just get a blast of nostalgia from these now vintage models. News Source: MotorWeek via YouTube Chevrolet Ford Jeep SUV Off-Road Vehicles Classics Videos Ford Bronco chevy blazer

2015 Ford F-150 gets Power Wheels treatment [w/video]

With the introduction of its forthcoming 2015 F-150, Ford is breaking with convention by shifting from steel-intensive construction to aluminum. But what if it weren't made of metal altogether? What if it were made of plastic instead, and packed an electric motor instead of an internal-combustion engine?
Feast your eyes, boys and girls, on the new Power Wheels F-150. Built by Fisher-Price and licensed by Ford, the third-generation ride-on toy started development nine months before the full-size version debuted at the Detroit Auto Show this past January, and is hitting sidewalks and driveways across the country this September.
The Power Wheels F-150 carries a sticker price of $349.99, and there's a special version at Toys R Us with LED headlamps (just like the real F-150) for an extra $10.