03 Ford Explorer Xlt 4wd V6 3rd Row Leather Sunroof 4x4 Clean Carfax on 2040-cars

Auto blog

Our interview with Jeremy Clarkson and James May, plus SEMA! | Autoblog Podcast #491

This week, David Gluckman and Mike Austin talk SEMA madness, mis-aligned steering wheels, wireless charging, McLarens (they're sports cars!), and decals. We also have an excerpt from a recent interview with James May and Jeremy Clarkson of The Grand Tour and Top Gear fame. As always, we talk about a variety of cars we've been driving and then respond to some questions from listeners. And as a bonus, there's a trivia question mixed in. The rundown is below. Remember, if you have a car-related question you'd like us to answer or you want questionable buying advice of your very own, send a message or a voice memo to podcast at autoblog dot com. Oh, and please send trivia questions! You'll get the honor of stumping your fellow listeners, and we'll thank you too. Autoblog Podcast #491 The video meant to be presented here is no longer available. Sorry for the inconvenience. Topics and stories we mention Stars Selling Cars The Ford Flex is dying SEMA! Dodge Durango Shaker concept New Mercedes inline-six engines Our interview with Jeremy Clarkson and James May Mercedes-Benz E-Class McLaren 570S Ad of the Week: Volvo ABCs of Death Spend My Money on used cars Rundown Intro - 00:00 The news - 02:15 Clarkson/May interview excerpt - 17:12 What we've been driving - 21:12 Ad of the Week - 39:02 Spend My Money/listener questions - 44:13 Total Duration: 57:05 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Feedback Email – Podcast at Autoblog dot com Review the show in iTunes Celebrities Podcasts SEMA Show Cadillac Dodge Ford McLaren Mercedes-Benz Volvo ford flex the grand tour mclaren 570s SEMA 2016

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.