Find or Sell Used Cars, Trucks, and SUVs in USA

2007 Ford Limited on 2040-cars

US $13,750.00
Year:2007 Mileage:98008 Color: Gray /
 Black
Location:

Paterson, New Jersey, United States

Paterson, New Jersey, United States
Advertising:
Fuel Type:Gas
For Sale By:Dealer
Engine:8
Transmission:Automatic
Body Type:SUV
Vehicle Title:Salvage
Condition:

Used

VIN (Vehicle Identification Number)
: 1FMFK20597LA78891
Year: 2007
Make: Ford
Model: Expedition
Disability Equipped: No
Doors: 4
Mileage: 98,008
Drivetrain: Four Wheel Drive
Sub Model: Limited
Trim: EL Limited Sport Utility 4-Door
Exterior Color: Gray
Drive Type: 4WD
Interior Color: Black
Number of Cylinders: 8

Auto Services in New Jersey

Woodstock Automotive Inc ★★★★★

Auto Repair & Service
Address: 700 Berkshire Valley Rd, Succasunna
Phone: (973) 208-3060

Windrim Autobody ★★★★★

Automobile Body Repairing & Painting, Automobile Parts & Supplies, Auto Body Parts
Address: 1339 Windrim Ave, Delran
Phone: (215) 455-5205

We Buy Cars NJ ★★★★★

Used Car Dealers, Wholesale Used Car Dealers
Address: 5 John St, Avenel
Phone: (888) 726-1103

Unique Scrap & Auto - USA ★★★★★

Automobile Parts & Supplies, Recycling Centers, Scrap Metals
Address: 470 Chandler Rd, Monroe-Twp
Phone: (855) 656-3825

Turnersville Pre-Owned ★★★★★

Auto Repair & Service, Used Car Dealers, Automobile Diagnostic Service
Address: 2880 Route 42, New-Gretna
Phone: (856) 740-0221

Trilenium Auto Recyclers ★★★★★

Automobile Parts & Supplies, Automobile Salvage, Used & Rebuilt Auto Parts
Address: 147 Tennent Rd, Morganville
Phone: (732) 591-0006

Auto blog

Watch NASCAR racer Brad Keselowski do a burnout... in a hotel conference room

Fri, 08 Mar 2013

A vast majority of hotels frown upon smoking inside the building these days, but Brad Keselowski doesn't follow the rules. During his introduction at the 2013 MiilerCoors Distribution Convention, the reigning NASCAR Sprint Cup champion smoked the tires of his Miller-sponsored Ford Fusion stock car, adding a pair of thick, black stripes to the carpeting of the Marriott World Center's conference room.
This definitely isn't a high-quality video, but it's the perfect vantage point to watch Keselowski lay down some rubber and receive a well-deserved standing ovation after pulling up in front of the crowd. Check out the short-but-sweet video posted below.

Airbag recall widens to include BMW, Chrysler, Ford and Toyota

Mon, 23 Jun 2014

The recall of faulty airbag inflators supplied by Takata has exploded today to grow to seven automakers. In most cases, only models in certain high-humidity regions were affected because the National Highway Traffic Safety Administration found in its investigation that moisture played a roll in determining whether there would be a problem. However, some companies opted for national campaigns. The exact number of affected models for these campaigns isn't yet known at this time.
BMW is recalling an undisclosed number of 325i, 325Xi, 330i and 330Xi models from the 2001 through 2005 model years and the 2001-2006 model year versions of the 325Ci and 330Ci for the driver side and passenger side inflators. Only vehicles currently registered in Florida, Puerto Rico, Hawaii and the US Virgin Islands are covered under this recall.
Neither Chrysler's filing with NHTSA nor its press release list the specific models affected, but a company spokesperson told Autoblog that at this time it only covers the driver and passenger side inflators for the 2006 Dodge Charger in Florida, Puerto Rico, Hawaii and the US Virgin Islands

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Thu, 13 Feb 2014

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.