2005 Ford Excursion =>$8000 on 2040-cars

Auto blog

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford Everest Concept shows China also has an affinity for big trucks

The Ford Everest Concept SUV at the 2014 Beijing Motor Show shows the future of the Blue Oval's truck line in China. While a concept for now, we're told that JMC, Ford's Chinese joint-venture partner, will build a production version sometime in the near future.
With design from Ford's Asia Pacific design team, the handsome seven-passenger SUV shows off some very muscular styling with wraparound headlights that hook into the contours of the angular trapezoidal grille. The beltline rises up the body in the rear and makes the back appear higher than the front. The rear is made from hard, chiseled contours that give the truck a very tough look. The Everest looks ready for some rough roads.
Ford is keeping the interior and mechanical details about the Everest a secret for now, but the SUV is rumored to share some components with the overseas Ranger pickup. The company has no plans to sell the truck in North America. Scroll down to read the official announcement, including the few details on its production.