2001 Ford Excursion Limited/4wd/7.3l Diesel / Lifted/ One Of A Kind Automatic 4- on 2040-cars

Auto blog

2015 Ford Mustang EcoBoost loses big power on 87 octane

The 2015 Ford Mustang with the 2.3-liter EcoBoost four-cylinder is a pretty potent package on paper. With 310 horsepower and 320 pound-feet of torque, it boasts better performance numbers than the 3.7-liter V6, but with better fuel economy as an added benefit. However, if you're in the market for one of these boosted 'Stangs, you should probably keep in mind that it really prefers to gulp premium, 93-octane fuel. It can drink 87-octane swill in a pinch, but you're going to find significantly less power underfoot when pulling away. While it's not shocking that the ponies are dialed back with a lower grade of gasoline, an alleged page from a Ford training manual obtained by Mustang 6G purports to show just how much power is lost, though. According to this document, the 2.3-liter EcoBoost makes 275 horsepower and 300 pound-feet of torque when running on lower octane fuel. That's a substantial reduction of about 11.3 percent compared to when the engine drinks 93 octane. Interestingly, according to Mustang 6G, that finding was a bit better than expected, because a Ford engineer reportedly said power would be down about 13 percent without altering peak torque. In speaking with Autoblog, Paul Seredynski of Ford powertrain communications, objected to part of this document. While he couldn't confirm the specific losses listed for the Mustang EcoBoost, "torque remains unchanged" with lower octane gasoline, Seredynski said. He speculated this training manual page was "possibly from before the engine was certified" and therefore showed incorrect figures. Serendynski did confirm that the automaker recommends using 93 octane, and like all modern engines, the software adapts if it's lower. "Peak power would be reduced" by using a lesser grade, he confirmed. Featured Gallery 2015 Ford Mustang EcoBoost: First Ride View 20 Photos News Source: Mustang 6GImage Credit: Copyright 2015 AOL, Ford, Mustang 6G Ford Technology Convertible Coupe Performance ecoboost ford mustang ecoboost

First 1K next-gen Mustangs to carry 2014 1/2 model year?

A new report from Mustangs Daily, citing insider sources at Ford, tells us that the Blue Oval will produce 1,000 next-generation Mustangs with the model year designation of 2014 ½, to celebrate the 50th anniversary of the storied marque. The commemorative half-year designation is a rumor that's been swirling in Mustang forums for quite some time now, and seems more plausible than ever with this most recent report. Certainly it's not far-fetched to believe that Ford will want to make a big deal of the golden anniversary for its most-loved model.
The story (compiled by Drew Phillips, who runs the aforementioned Mustang site when he's not directing the photography on these pages) goes on to say that the limited-run cars will be the first built on the new Mustang platform internally known as S550 (and spied testing in the attached gallery). Each car is said to carry a "special" VIN and build number, though no performance upgrades versus the 2015 cars to follow are in the works. A collector's dream then, rather than a weekend racer's.

NHTSA closes Ford F-Series Super Duty steering probe without recall

The National Highway Traffic Safety Administration's investigation into 2008 Ford F-250 and F-350 Super Duty pickups, which was originally opened last year, has now ended without a recall. NHTSA was looking into steering failures on some 336,000 trucks.
The issue rested with the steering gear - NHTSA received five complaints of failures - which was redesigned in 2005. According to the report on the matter, investigators "found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload."
NHTSA investigators, however, "found no evidence of fatigue or material property defects in any of the fractures. Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns," according to the report, obtained by The Detroit News.