2013 Ford Escape Se on 2040-cars

Auto blog

Massive Airbag Recall Affects Seven Automakers

The recall of faulty airbag inflators supplied by Takata has exploded today to grow to seven automakers. In most cases, only models in certain high-humidity regions were affected because the National Highway Traffic Safety Administration found in its investigation that moisture played a role in determining whether there would be a problem. However, some companies opted for national campaigns. The exact number of affected models for these campaigns isn't yet known at this time. BMW is recalling an undisclosed number of 325i, 325Xi, 330i and 330Xi models from the 2001 through 2005 model years and the 2001-2006 model year versions of the 325Ci and 330Ci for the driver side and passenger side inflators. Only vehicles currently registered in Florida, Puerto Rico, Hawaii and the US Virgin Islands are covered under this recall. Neither Chrysler's filing with NHTSA nor its press release list the specific models affected, but a company spokesperson told Autoblog that at this time it only covers the driver and passenger side inflators for the 2006 Dodge Charger in Florida, Puerto Rico, Hawaii and the US Virgin Islands In most cases, only models in certain high-humidity regions were affected because the NHTSA found that moisture played a roll in determining if there would be a problem. Ford is recalling an estimated 58,669 cars that include the 2005-2006 model years of the Ford GT for the driver and passenger inflators, the 2007-2007 model years of the Mustang for the driver side and 2004 Ranger for the passenger side. It covers vehicles originally sold or currently registered in, wait for it... Florida, Puerto Rico, Hawaii and the US Virgin Islands. Honda is issuing three separate recalls regarding the problem. First, the company is recalling the 2002-2003 model years Civic, CR-V and Odyssey and the 2003 model year of the Accord, Element, Pilot and Acura MDX to replace the passenger's side inflator. This covers all models nationwide. Second, Honda is repairing the passenger's side airbag inflator in the 2003-2005 Accord, Civic, CR-V, Element, Pilot, the 2003-2004 model year versions of the Odyssey, the 2003-2005 model year Acura MDX and 2005 Acura RL. However, only for vehicles located in Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico and the US Virgin Islands. Owners will be notified in July. Finally, Honda is separately replacing some models' driver's side inflators.

Ford making Fusion production moves to challenge Camry on volume

The Ford Fusion may already beat the Toyota Camry in terms of models offered, transaction price and sales increase so far this year, but if the Fusion wants to make a run at the title of best-selling car in the US, Bloomberg reminds us that volume is key. Opening a second production line at the Flat Rock, MI assembly plant will reportedly allow Ford to produce around 350,000 Fusions annually, which compares Toyota's ability to crank out 475,000 Camrys and Honda's capacity to build around 450,000 Accords.
For the Fusion, that's an extra 100,000 units compared to the car's current pace, and the article adds that the Fusion is "Ford's best shot" to regain the passenger car sales crown - a title it (or any other US automaker, for that matter) hasn't held since the mid-1990s. Despite hiccups with recalls and fuel economy numbers, the Ford Fusion is still red hot when it comes to sales. Fusion sales are up 13 percent so far this year (compared to a 0.6 percent decrease for Camry), and its average transaction price of $26,343 is about $2,300 more than its rival from Toyota.
The Fusion's popularity has helped Ford improve its sales in California; the Dearborn-based automaker has a market share of 18 percent in the state, which is just a fraction of a percentage behind Honda. And this popularity should continue as Ford ups Fusion production and expands the model lineup even further for 2014 with a new 1.5-liter EcoBoost engine soon to become an option.

This is what a 3D-printed liquid metal Ford Torino looks like

Artist Ioan Florea has encapsulated a 1971 Ford Torino with 3-D-printed liquid metal transferred onto the car using technology that he developed, and the result is a stunningly shiny, seamless design.
"The surface has the highest coefficient of reflectivity never achieved before," Florea told us in an e-mail, using "nano-materials and nano-pigments that create an internal three-dimensional structure and dictate the polymer how to behave." Sure... We'll leave it to him to make any more 3-D-printed liquid metal-transferred art pieces.
Florea grew up in Romania, and the motivation behind picking the old Ford as his canvas came from his childhood memories of what an American car is - "big and wide and fascinating," he says - and the European name of the car itself, which it shares with an Italian city.