2012 Limited Used Turbo 2l I4 16v Automatic Front Wheel Drive Suv on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ford builds Lightweight Concept with Fusion shell [w/video]

It's a fairly well known fact that removing weight from a car is essentially a panacea for many of the modern automobiles problems. Does it handle like crap? Remove weight. Underpowered? Don't add power; trim the fat. Need to improve fuel economy? It's diet time.
Actually executing a major weight reduction program, though, much like with human beings, is no easy task. Unlike you or I, where motivation is the issue, the prohibitive measure in trimming a car's waistline is money. Lightweight materials are expensive, with carbon fiber and carbon-fiber reinforced plastic still primarily in the domain of higher end vehicles. Even aluminum construction, pioneered on a mass-produced level by Audi and Jaguar, is only now starting to make its way into the mainstream, thanks to the upcoming Ford F-150.
With this concept, though, Ford is attempting to show that a mass-produced, lightweight vehicle isn't too far off. This is the Lightweight Concept, and while it may look like a Fusion, it weighs as much as a Fiesta. For reference, the lightest Fusion available to the public is the 3,323-pound, 2.5-liter model with a manual transmission. A manually equipped, 1.6-liter Fiesta, meanwhile, is just 2,537 pounds.

2015 F-150 launch to curb Ford profits?

Ford is making a big bet on aluminum with its new 2015 F-150, and it's possible that the decision will hurt the company financially, at least in the short term. After earning a record $8.6 billion in 2013, the Blue Oval does not expect to set another record in 2014. According to Automotive News, that's "largely attributable to F Series," says Bob Shanks, Ford's Chief Financial Officer.
To retool for the new F-150, Ford will idle its Dearborn Truck Plant in Michigan for 11 weeks and the Ford Kansas City Assembly Plant in Missouri for 2 weeks. "3 of the 13 overall weeks occur during what normally is our summer shutdown timeframe," said Mike Levine, Ford Trucks Communication Manager, in an email to Autoblog. The extra 10 weeks will be preparing for the more aluminum-intensive construction for the trucks and will mean over 2 months of no F-150s being made. For comparison's sake, Chrysler boss Sergio Marchionne just confirmed that the 200 plant in Sterling Heights, MI will be down for 30 days to retool for the new model, but obviously there are many more F-150 production variables than for the midsize sedan.
Levine notes that Ford is already running three shifts at both plants, and says the automaker has plans to ensure that there is adequate supply of the full-size pickups during the retooling process. The company does not want to suffer a shortage of the vehicle that accounted for 31-percent of its 2013 US sales and an even bigger percentage of its profits.