Ford Crown Victoria Lx ~one Owner!~ Clean! Seats Six! on 2040-cars

Auto blog

Ward's reveals annual 10 Best Engines list for 2013

Ward's Auto has released its annual 10 Best Engines award winners. The 2013 list covers the full width and breadth of the internal combustion spectrum, from a spate of efficient four-cylinders to the most powerful production V8 on the planet. As always, the entries must be available in a production vehicle in the first quarter of 2013 with an MSRP of less than $55,000. The supercharged 3.0-liter V6 from the Audi S5 held on for the fourth consecutive year, and BMW earned two spots on the list with its turbo 2.0-liter four-cylinder and turbo 3.0-liter inline-six.
Ford pulled in two awards for its 2.0-liter EcoBoost four-cylinder and and the supercharged 5.8-liter V8 from the Shelby GT500. Honda matched BMW and Ford with two wins of its own. Wards awarded the 2.4-liter four-cylinder from the Honda Accord Sport as well as the 3.5-liter V6 from the Honda Accord. Chrysler, General Motors and Subaru each garnered a spot on the list as well for the 3.6-liter V6 in the Ram 1500, the turbo 2.0-liter four-cylinder in the Cadillac ATS and the 2.0-liter four-cylinder the Subaru BRZ, respectively. You can read the full press release below for more information.

Massive Airbag Recall Affects Seven Automakers

The recall of faulty airbag inflators supplied by Takata has exploded today to grow to seven automakers. In most cases, only models in certain high-humidity regions were affected because the National Highway Traffic Safety Administration found in its investigation that moisture played a role in determining whether there would be a problem. However, some companies opted for national campaigns. The exact number of affected models for these campaigns isn't yet known at this time. BMW is recalling an undisclosed number of 325i, 325Xi, 330i and 330Xi models from the 2001 through 2005 model years and the 2001-2006 model year versions of the 325Ci and 330Ci for the driver side and passenger side inflators. Only vehicles currently registered in Florida, Puerto Rico, Hawaii and the US Virgin Islands are covered under this recall. Neither Chrysler's filing with NHTSA nor its press release list the specific models affected, but a company spokesperson told Autoblog that at this time it only covers the driver and passenger side inflators for the 2006 Dodge Charger in Florida, Puerto Rico, Hawaii and the US Virgin Islands In most cases, only models in certain high-humidity regions were affected because the NHTSA found that moisture played a roll in determining if there would be a problem. Ford is recalling an estimated 58,669 cars that include the 2005-2006 model years of the Ford GT for the driver and passenger inflators, the 2007-2007 model years of the Mustang for the driver side and 2004 Ranger for the passenger side. It covers vehicles originally sold or currently registered in, wait for it... Florida, Puerto Rico, Hawaii and the US Virgin Islands. Honda is issuing three separate recalls regarding the problem. First, the company is recalling the 2002-2003 model years Civic, CR-V and Odyssey and the 2003 model year of the Accord, Element, Pilot and Acura MDX to replace the passenger's side inflator. This covers all models nationwide. Second, Honda is repairing the passenger's side airbag inflator in the 2003-2005 Accord, Civic, CR-V, Element, Pilot, the 2003-2004 model year versions of the Odyssey, the 2003-2005 model year Acura MDX and 2005 Acura RL. However, only for vehicles located in Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico and the US Virgin Islands. Owners will be notified in July. Finally, Honda is separately replacing some models' driver's side inflators.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).