2006 Ford Crown Victoria Police Interceptor Sedan 4-door 4.6l on 2040-cars

Auto blog

Ford recalling nearly 700k Escape CUVs, C-Max hybrids over two separate safety issues

Poor Escape. Ever since its launch in 2012, Ford's small CUV has been the subject of many, many, many recalls. And today, The Detroit News is reporting that Ford is adding two more recalls to the 2013-14 model year Escape's permanent record, one of them also involves the C-Max hybrid hatchback.
The first recall, covering 692,500 Escape and C-Max vehicles, is due to a software glitch that could cause the airbags - specifically, the safety canopy - to not deploy in a timely fashion during rollover crashes. According to the News, Ford says no crashes or injuries have been reported in relation to this problem.
The second recall, covering 692,700 Escapes, is related to the door handles. The News reports that the exterior door handles could open while the vehicle is in motion, and could also fail to latch properly. Once again, no crashes or injuries have occurred because of this. The National Highway Safety Traffic Administration has not issued an official notice on either recall as of this writing.

Recharge Wrap-up: Ford 1.0L EcoBoost a hit in Europe; Build a tiny inverter, win $1 million

In Europe, Ford's 1.0-liter EcoBoost engine is the best-selling turbocharged gasoline engine. The three-cylinder motor powers 20 percent of new Fords sold in Europe. Earlier this year, it won its third International Engine of the Year award, and between January and June, it was sold in about 120,000 cars. So far this year, 38 percent of Fords sold in the Netherlands, 35 percent in Denmark and 32 percent in Switzerland have been powered by the 1.0-liter EcoBoost. The engine's turbocharger spins at 248,000 rpm, and provides 24 psi of pressure. The engine produces up to 138 horsepower, depending on the version. Read more in the press release below. When lithium-ion battery packs are retired from the road, remanufacturing, repurposing, and recycling are worthwhile options, according to a study by Mineta Transportation Institute. The study included a cost-benefit analysis of those three options, and found remanufacturing to be the best route. To get the most out of them, batteries should be tested and have their damaged cells replaced then put back to use. Repurposing is the second best option, using the remaining available charge for something besides cars. Recycling on its own isn't profitable, but it could make economic sense with "increased technological breakthroughs." Learn more at Recycling International or download the report here. A smaller inverter for EVs can win you $1 million. The Little Box Challenge is an open competition to build a power inverter with a density of at least 50 watts per cubic inch. Google and the Institute of Electrical and Electronics Engineers (IEEE) are offering the hefty prize to the team that builds the inverter with the highest power density within an enclosed volume of 40 cubic inches. Teams must register by September 30. Read more at Green Car Congress or learn more at the Little Box Challenge website.

Ford rethinking vehicle launch strategy

With a new boss at the helm, Ford is looking at new ways to improve its vehicle launches in North America to prevent recent issues that have popped up with models like the Lincoln MKZ, Ford Escape and Ford Fusion. Speaking with Automotive News, Ford's new president of the Americas, Joe Hinrichs, revealed a few ways the automaker plans to avoid early build issues such as the engine fires on certain 2013 Escape and Fusion models and months-long delays for customers to receive their MKZs.
It sounds like the root of the problems may have been Ford's relationship with suppliers compounded by the fact that the product surge came on the heels of the recent industry-crippling recession, and in the AN article, Hinrichs says improvements are being made to reduce problems during the launch of new or redesigned models. Three such improvements that were implemented during the first quarter of this year including more rigorous quality comparisons, better use of computer technology to catch major problems sooner and hiring engineers to work closer with suppliers.