1978 Ford Bronco Custom Sport Utility 2-door 6.6l on 2040-cars

Auto blog

Ford recalls more than 550,000 trucks and SUVs for various safety issues

Ford announced safety recalls for its current F-150 pickup along with several Ford and Lincoln crossovers early Wednesday. The recalls cover more than 550,000 vehicles and address various safety defects, ranging from a fire hazard to potential loss of braking power.  The most far-reaching of the recalls covers approximately 550,000 examples of the 2015-2018 Ford Edge and 2016-2018 Lincoln MKX, which may have been assembled with defective front brake jounce hoses (also commonly referred to as "flex lines"). These hoses run from fixed points on the chassis to the individual front brake calipers. Defective hoses could potentially rupture, allowing brake fluid to leak and resulting in a loss of braking function. Ford will replace the components in question with revised parts.  The next-largest recall is for roughly 3,000 2020 Lincoln Corsair crossovers. The affected models may have been assembled without proper clearance between their rear suspension springs and toe link brackets. The components could potentially make contact, wearing down the protective coating on the rear coil springs, allowing corrosion to occur over time. This corrosion could eventually lead to a failure of the spring. If this happens while the vehicle is being driven, it could result in a sudden change to the vehicle's handling characteristics, and the spring fragments could potentially cause further damage to the car or surrounding traffic.  Ford says owners will be notified that their Corsairs need to be inspected; if there is not adequate clearance between the rear suspension components, Ford's service technicians will remove material from the toe link bracket to allow for operation without contact.  The final (and by far the smallest) recall is for the 2020 F-150. Some units may have left the factory with the incorrect retention nut on the hot lead to the starter motor. Ford says it can cause increased heat generation or electrical arcing, which could potentially result in a fire. Ford says this issue is limited to just a few hundred examples sold in the United States. Dealers will inspect the vehicles and replace the nut if necessary.       

10 automakers shack up in Detroit hotel to talk Takata airbags

Since Takata has decided not to take the lead concerning potential issues with its airbag inflators, the automakers have. Perhaps that's unsurprising, since it's the automakers, not Takata, that will take a beating on the dealership floor if consumers decide its models are a health hazards. The Detroit News reports that Toyota, Honda, General Motors, Ford, Chrysler, Mazda, BMW, Nissan, Mitsubishi and Subaru met in a hotel conference room near the Detroit Metropolitan Airport last week to sort out a way to understand the technical issues involved. So far, faulty airbag inflators have been ruled the cause of five deaths and 50 injuries around the world, but neither Takata nor investigators understands exactly why the inflators are malfunctioning. The National Highway Traffic Safety Administration recently asked Takata to issue a national recall, Takata declined, citing a minuscule failure rate and the fact that it's still investigating the issue. Toyota and Honda then made an industry-wide appeal for "a coordinated, comprehensive testing program" that would pinpoint the problem inflators and get them replaced, and that's what the Detroit meeting was about. Numerous issues, however, will make this a long row to hoe: simply getting the parts to replace the nearly 20 million inflators in cars recalled around the world so far - even working with other suppliers - will take a years, but more importantly, no one knows if the replacement inflators currently being installed will suffer the same issue. Answers will hopefully come quickly with Takata, the ten automakers and NHTSA all independently investigating the problem.

Ford debuts Fusion NASCAR racer that edges closer to stock [w/video]

The sixth-generation NASCAR Sprint Cup racecar, which will make its competition debut at the 2013 Daytona 500 this weekend, marks the closest thing to a "stock car" that the sport has seen in more than 20 years. No longer using just stickers to distinguish the different brands, the image above shows the lengths NASCAR and automakers went in order to create a racecar design that more closely resembles the individual cars they represent.
Ford, one of the more open and vocal OEMs regarding the Gen6 car's development, is giving us a closer look at its racing version of the Fusion with a pretty revealing side-by-side comparison with last years' racer (click above for an expanded view). Aside from the more realistic front end and production-like body lines, the overall shape, dimensions and proportions have also been designed to give the racecar a more stock appearance. Most of the new racer was designed by the Ford Design Center, which the automaker says was the first time it has been so involved in the design process since the 1960s. Of course, one area the Sprint Cup Fusion really differs from the production Fusion is its Ford Racing 5.8-liter V8 producing around 850 hp. Can you say Fusion SVT?
Scroll down for a quick video from Ford Racing showing a production Fusion morph into a Cup car.