Dodge Viper Rt-10 on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

The last time Dodge recycled the Demon name, it was for a Miata fighter

We and the rest of the automotive world are eagerly awaiting the reveal of the Dodge Challenger Demon. And why wouldn't we be? It's going to be a Hellcat, but with less weight, bigger fenders, more performance, and more Vin Diesel. This isn't the first time we've been excited about a Demon from Dodge, though. Ten years ago, Dodge had another demonic car, but it was very different from the new one. The Demon of 2007 was a lithe little roadster that looked primed and ready to take on the Miata, as well as the now-departed Solstice and Sky twins. The Demon was just under an inch shorter than the MX-5 and the Solstice, and it packed a 172 horsepower 2.4-liter four-cylinder that fell right between the Miata's 170 and the Solstice's 177 outputs. Dodge's estimated the curb weight, which for a concept is largely theoretical, also slotted between the two cars at 2600 pounds. That was about 150 more than the Mazda, and about 200 less than the Pontiac. The pitch perfect specifications were presented in a crisp two-seat roadster wrapper. In many ways, it looked like a baby Viper, with a menacing crosshair grille, slanted headlights, and fat rear fenders. The Demon's line's were brutally simple and geometric, too. They didn't seem far removed from the first-generation Audi TT. The interior was also plain and simple. The key highlights were a horizontal aluminum accent that ran the width of the dash, echoed by an aluminum-covered center console. The instrument cluster was uncluttered, with just four gauges, and the only controls were some climate knobs, a double-DIN head unit, and a six-speed manual. It turns out that the 2007 Demon didn't drive very well, though. You see, we actually drove this concept back in the day, and like many concepts, it still had a long way to go to be production ready. The gearbox would grind, the ride quality was terrible. However, the interior was roomy, and the engine sounded suitably grumbly, if a bit coarse. At the time, we said Dodge should absolutely build the little roadster. In retrospect, the company probably made the right decision not to invest in the Demon. The small rear drive sports car segment was, and still is, an extremely niche market. It would have been a big investment for little return, something FCA today is trying to avoid. This is all before taking into account the fact that the recession was just around the corner. In the end, we can't be too sad though.

Dodge recalls 27k Darts for bracket that can disrupt transmission module

Dodge is recalling 27,520 examples of the 2013-2015 Dart with dual-clutch gearboxes. The mounting bracket for the transmission control module can affect the part's operation and cause the compacts to suddenly shift into neutral. According to the automaker, 23,688 of them are in the US, 3,376 in Canada, 5 in Mexico, and 451 elsewhere. The National Highway Traffic Safety Administration reports these examples carry build dates between February 24, 2012, and June 16, 2015. There are also no reports of accidents or injuries. Because of the way the bracket is mounted, the part can put too much force on the control module's circuit board and cause it to shift out of gear. The engine and airbags remain operable if this happens. To fix things, dealers will install a redesigned mount and replacement module. Related Video: Statement: Mounting Bracket September 14, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 23,688 cars in the U.S. to replace certain control modules and mounting brackets that may contribute to a loss of motive power. The Company is unaware of any related injuries or accidents. An FCA US investigation prompted by a small number of warranty claims discovered a control-module mounting bracket may apply too much force and disrupt the function of a circuit board within the module. This condition, unique to certain cars equipped with dual dry-clutch transmissions (DDCT), may cause the transmission to shift into neutral. However, the engine remains on and the vehicle's air-bags, as well as other safety features, are unaffected. The condition may also be preceded by the illumination of a dashboard warning light. Customers who observe this are urged to contact their dealers. The campaign is limited to certain 2013-2015 Dodge Darts equipped with DDCTs. Additional vehicles will be recalled in Canada (3,376), Mexico (five) and outside the NAFTA region (451). Affected customers will be advised when they may schedule service, which will be performed free of charge. Service will entail installation of a redesigned mounting bracket and replacement of the control module. Customers with additional questions may call the FCA US Customer Information Center at 1-800-853-1403.