2000 Dodge Viper R/t-10 Convertible 2-door 8.0l on 2040-cars

Auto blog

Hennessey's Dodge Challenger Hellcat cranks out 1,032 hp

Enthusiasts know the Dodge Challenger Hellcat produces 707 horsepower. It's one of the modern muscle-car era's iconic numbers. But for some, that's not enough. Enter Hennessey Performance. The Texas tuners loaded the Hellcat with a twin-turbocharger that works with Dodge's supercharger to boost output to 1,032 hp and 987 pound-feet of torque. Yes, that's an engine dyno rating, not at the rear wheels, but still! It's a little more complicated than a bolt-on booster. Called the HPE1000, the turbo kit has stainless steel headers and down pipes, billet aluminum compressor wheels, and a high-flow air system. There's also an an improved fuel pump, and the engine and chassis are specially calibrated. You also get numbered plaques signed by John Hennessey himself and the engine tech who builds your mill. All of this helps get your Hellcat to 60 miles per hour in 2.7 seconds, and it can do the quarter mile in 9.9 seconds at 142 mph. The Hellcat and it's 6.2-liter blown Hemi V8 are not for the faint of heart. Hennessey makes this Dodge downright demonic. Related Video: Related Gallery 2015 Dodge Challenger SRT Hellcat View 23 Photos Image Credit: Hennessey Performance Dodge Coupe Performance

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Fiat-Chrysler shows its SEMA lineup

Fiat Chrysler Automobiles already previewed its 2014 SEMA show lineup with some slick renders. Now, the automaker has finally showed us the actual cars, and among the group there are definitely some that stand out more than others.
Dodge is really showing off its muscle at this year's show with four concepts that all pump up the power of the brand's models. Perhaps most interesting among them is the Challenger T/A Concept (pictured above) in striking Sublime Green and matte black. It's meant to resemble the classic Trans Am racer from the '70s. Under the hood is a 6.4-liter V8, and to fit the vintage style there's a pistol-grip gearshift inside.
The Charger R/T also gets some attention with the Mopar concept that shows off what FCA's aftermarket performance arm can do. Mods include an updated body kit, cold-air intake for the 5.7-liter V8 and a coil-over suspension kit. Beyond that, the Dart R/T Concept looks a lot meaner with a black hood with duct work that leads straight to the air intake. The rest of the compact sedan is dolled up in O-So-Orange paint and is fitted with upgrades to improve handling like a coil-over suspension and big brake kit from the Mopar catalog.