Dodge Ram 3500 Slt Cummins on 2040-cars

Auto blog

Will airbags sandbag the 2017 Dodge Viper?

The Dodge Viper is speeding down the road to cancellation for the 2017 model year, and at least part of the reason for the V10 monster's death is a problem fitting it with federally mandated side curtain airbags. An anonymous source close to FCA US told Motor Trend the automaker can't install the parts because they would further limit the coupe's already tight headroom. The government believes the side curtain airbags can reduce occupant ejections during accidents, and all vehicles must have them for the 2017 model year. The Viper's slow sales also don't provide FCA US much motivation to work out a solution to this problem. The automaker moved just 676 of the handmade sports coupes in the US in 2015, which was down 11 percent from 760 deliveries in 2014. FCA CEO Sergio Marchionne hinted at the Detroit Auto Show that the Viper could return eventually. He doesn't like that the current model has a dedicated platform but indicated a new one could share the underpinnings with another of the company's products. Marchionne's current business plan for FCA stresses building the automaker's value, so it might be a while before we see the sweater-clad CEO focusing on a niche vehicle like the Viper. Related Video:

SRT reveals Satin Vapor Edition 300, Charger and Challenger SRT models

With the exception of some notable truck and van introductions, Chrysler brands have tended to use the Chicago Auto Show to bring out new special editions, pimp their aftermarket parts support or indulge in the occasional flight of fancy. That plan is holding true for 2014, as well. Cases in point are these new Satin Vapor Editions of the 2014-model-year Dodge Challenger, Dodge Charger and Chrysler 300 - all from SRT.
The Satin Vapor name may sound like a failed 1970s glam-rock band, or a pseudo-gynecological diagnosis from the Old West, but is, in fact, pretty much a tape-and-trim package for this trio of hi-po Mopars. 300, Challenger and Charger alike come shod with 20-inch aluminum wheels finished in Black Satin Vapor Chrome, and are accented with Satin Black bits aplenty. The 300 gets blacked-out mirrors, spoiler and roof; the Challenger applies it to mirrors and its fuel door; while the Charger has the stuff covering its roof, hood and Super Bee tail graphic.
Interiors of the cars have been mildly updated as well, with all three getting some combination of Nappa leather, ultra-suede and carbon-fiberish finishes.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.