1996 Dodge Ram 3500 Long Bed on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Dodge Challenger spied exercising supercharged Hellcat Hemi V8

One of the prime complaints against the Dodge Challenger is that, even in SRT8 guise, its 470 horsepower is responsible for hauling over 4,200 pounds of vehicle. For comparison, the 420 hp in the Ford Mustang GT only has to deal with 3,618 lbs. Things only get worse from there, as the higher-performance variants of both the Mustang and the Chevrolet Camaro are far more powerful than an SRT8 without adding on much heft.
So what is Chrysler to do? The correct answer is add a whole lot more grunt to its hefty two-door and even the odds. That's where the all-new Hellcat engine comes into play. We reported on this engine in May, and suggested that the Hellcat, a supercharged powerplant based on a 6.4-liter V8, would easily generate 500 to 570 hp and could likely arrive boasting more than 600 ponies.
Chrysler's ace in its sleeve has now been spied testing, with a number of Hellcat-equipped Challengers running the potent new engine both in more urbanized areas and under the sun of Death Valley. The hoods on these testers have been raised to accommodate the engine, and that camouflage over the fascias of these prototypes is there to hide a larger air intake. We also note what appears to be a new split grille under wraps. As for power output, our spies are now suggesting a Viper-equalling 640 hp from the Hellcat-equipped cars.

Junkyard 1983 Dodge Rampage has Franco-American roots

Lee Iacocca and the K-Cars get most of the credit for saving Chrysler after the company's 1979 bailout by the US government, but the success of the Simca-derived Omnirizon platform was a large, if overlooked, component of Chrysler's early-1980s resurgence. The Dodge Omni and Plymouth Horizon were sold in the United States for the 1978 through 1990 model years, and variants included the 1983-1987 Dodge Charger and the Rampage, this well-worn example of which I spotted in a Denver self-service wrecking yard last week. The early Omnirizons came with a Volkswagen-sourced 1.7-liter engine, but all of the Rampage pickups (and their near-identical Plymouth Scamp siblings) came from the factory with a 2.2-liter K-Car engine making 96 horses. This truck has a 4-speed manual transmission, which would have made it reasonably quick by Malaise Era standards. This one had plenty of body filler and rust, even before the crash that sent it on that final tow-truck ride to this place, so it wouldn't have been worth restoring. Still, we can hope that some of its parts will live on in other L-body trucks. Related Video: Featured Gallery Junked 1983 Dodge Rampage in Denver View 16 Photos Chrysler Dodge Automotive History Truck Classics dodge rampage