2013 Dodge Ram 2500 Crew 4x4 Lifted Leather Diesel 22k! Texas Direct Auto on 2040-cars

Auto blog

Chrysler killing off the 200 Convertible, Dodge Avenger

When Chrysler rolled out the first-generation 200 to replace the Sebring range in 2010, it included replacements for both the sedan and the convertible. The Sebring Coupe, however, was left out of the mix. And now that the second-generation Chrysler 200 is descending upon us, Auburn Hills is paring things down even further. But this time, it's the convertible that reportedly isn't making the cut. Shame, too, since the rendering above shows what could have been quite an attractive droptop.
As our compatriots at Edmunds point out, sales of the convertible model accounted for less than five percent of overall Chrysler 200 sales, and at those numbers, the considerable cost of engineering a new drop-top couldn't be justified. With the Toyota Camry Solara and Volkswagen Eos also gone from the market (well, the VW isn't gone quite yet), the discontinuation of the Chrysler 200 Convertible leaves the affordable convertible segment largely to the sportier likes of the Ford Mustang and Chevy Camaro and smaller European offerings like the Mini Cooper and VW Beetle.
The Chrysler 200 Convertible isn't the only derivative being left behind with the new model: so too is the Dodge Avenger. That will leave a glaring hole in the Dodge lineup, with nothing to bridge the gap between the compact Dart and the larger Charger. Whether the Dodge brand has any plans to replace the Avenger with another model, not to be based on the 200, remains to be seen.

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.