1999 Dodge Ram 2500 Laramie Slt on 2040-cars

Auto blog

Why the Charger Hellcat can't be ordered with a manual transmission

Fans of truly irreverent amounts of horsepower will find lots to love in the form of the 2015 Dodge Challenger and Charger Hellcat models. Both of them send 707 ridiculous horsepower to the rear wheels; the only question is whether you want your absurdity delivered with two or four doors. Oh, and whether or not you want the option of a manual transmission.
If you prefer rowing your own gears, the choice is made for you; there is no manual gearbox option available on the Charger Hellcat, or any Charger model at all, for that matter. Wonder why? Well, besides the fact that almost nobody - sorry, clutch fans, but it's true - would choose to buy a Charger with a manual transmission, that is? The answer, according to an industry insider in a post written on Jalopnik's Opposite Lock forum, is the floorpan.
It's probably not a surprise to most of our readers that the Dodge Challenger and Charger share a large portion of their chassis structure, which is codenamed LX at Chrysler, but there are still some significant differences under the skin due to the shorter wheelbase and two-door coupe bodyshell of the Challenger, as opposed to the sedan shape of the Charger. One of the differences is the floorpan, the huge chunk of sheetmetal that makes up the floor of the car and props up such essential items as the car's seats.

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

FCA plants skipping summer shutdown to keep up with demand

Hopefully, some FCA US factory employees don't have big plans for the usual summer shutdown, because the automaker is keeping several plants running this year. Demand is so high that the company wants to keep models rolling off the assembly lines. Four FCA US assembly plants, all the engine factories, and some locations that build transmissions are staying open throughout the summer, according to the Detroit Free Press. Usually, these sites would see a two-week shutdown for the company to retool and perform repairs. This year, factories are staying open for FCA to support its strong sales. The lines that remaining humming through the summer show an inclination toward the automaker's popular SUV's and crossovers. They include the Jefferson North Assembly Plant in Michigan that builds the Jeep Grand Cherokee and Dodge Durango; Saltillo Van Assembly in Mexico that constructs the Ram ProMaster; Toledo Assembly Complex in Ohio that produces the Cherokee and Wrangler; and Toluca Assembly in Mexico that makes the Dodge Journey and Fiat 500. Related Video: News Source: The Detroit Free PressImage Credit: Bill Pugliano / Getty Images Plants/Manufacturing Dodge Fiat Jeep RAM FCA dodge journey fca us ram promaster Jefferson North Assembly Plant