2dr Reg Cab 5.7l Cd 4x4 Numbered Limited Edition Rumble Bee Hemi 20" Wheels on 2040-cars

Auto blog

Chrysler recalls AWD 300, Charger, Ram 1500 over ZF transmission

What do the Chrysler 300, Dodge Charger and Ram 1500 all have in common? Yes, they're all Chrysler products, and two of them are based on the same platform. And we're sure you could find more similarities between them all, but the common trait we're looking at here is that, while they all come standard in rear-drive form, they're also available with all-wheel drive. And it's the transmission in those models that's the subject of the latest recall notice issued by the National Highway Traffic Safety Administration.
The output shaft on the eight-speed automatic transmission supplied by ZF to Chrysler for the AWD versions of the 300, Charger and Ram 1500 is apparently prone to fracture. That in the end could leave the vehicle without power and could, according to the NHTSA investigation, increase the chance of a crash. The vehicle could also roll away if even if left in Park without the handbrake applied.
That's why Chrysler is calling in 4,194 examples of those three models from the 2013 model year. Dealers will be responsible for inspecting the transmissions and, where necessary, replace the entire unit. See the full recall notice below for all the details.

Weekly Recap: New bosses try to jump-start Cadillac and Lincoln

Both of America's domestic luxury brands seem to be stuck in neutral.
It's ironic that Cadillac and Lincoln got new bosses within days of each other this month. It's also a commentary on the fact both of America's domestic luxury brands seem to be stuck in neutral.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.