2001 Dodge Ram 1500 Van Base Standard Cargo Van 3-door 3.9l on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.

2025 SRT Hellcat concepts as previewed by high schoolers

Fiat Chrysler Automobiles has some very talented designers in its ranks. Like any good company, though, the automaker is always on the lookout for early talent. Even if they're still in high school. One of those talent-seeking initiatives is the company's Drive for Design contest, an event open to tenth-, eleventh-, and twelfth-grade students that are hoping for a future in design. For this year's event, students from across the country were given a shot to design their vision for a 2025 model-year Dodge SRT Hellcat. The results are impressive, as you can see in the gallery above. First place went to Ben Treinen, from Archbishop Moeller High School in Cincinnati. Second place was the only award to go to a student outside the Rust Belt, with Macon, GA's Harrison Kunselman, a student at Mount de Sales Academy taking the silver. Third place was won by a metro Detroiter – Bloomfield Hills High School student Hwanseong Jang, while fourth went to Andrew Gombac of Loyola Academy in Wilmette, IL. According to FCA, all four winners will have their sketches on display at the 2016 Autorama at Cobo Center at the end of February. They'll also win some pretty nifty prizes. First place will get a new Apple MacBook Pro, while second, third, and fourth get the new Apple iPad Pro and Apple Pencil (arguably just as good of a prize for budding designers). All four finishers will also attend a three-week automotive design course at Detroit's prestigious College for Creative Studies, have dinner with FCA designers, and score three passes to Autorama. FCA will cover travel and lodging to Auburn Hills. Read on for the official blast from FCA. Related Video: FCA US Design Team Announces Winners of Drive for Design Contest January 19, 2016 , Auburn Hills, Mich. - The FCA US LLC Design team today announced four winners in this year's Drive for Design contest. The FCA US Drive for Design contest challenged U.S. high school students in grades 10-12 to design a Dodge SRT Hellcat for the year 2025. "The Drive for Design contest continues to be a great way for the FCA US Design team to connect with students that show an interest in art and design," said Mark Trostle – Head of Dodge and SRT Design, FCA US LLC.