1987 Dodge Power Ram 4x4 No Rust Ever Restored on 2040-cars

Auto blog

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Roadkill builds crazy-cheap 1968 Dodge Charger rat rod using an old motorhome

Certain requests for description simply cannot be fulfilled, like if someone asked you to describe Picasso's Guernica or Gilliam's Brazil. There is only one appropriate answer to such entreaties, and that is: "You just gotta see it." That's where we are with the latest episode of Roadkill, wherein Messr's Freiburger and Finnegan dig out a 1968 Dodge Charger that Freiburger acquired in exchange for a set of cylinder heads, and intend to stuff it with the big-block motor from a long-bed, three-quarter ton Dodge pickup.
Only the pickup is too nice to tear apart, and the Charger needs a whole lot more lovin' - and parts - than initially expected. Enter, stage right, the Class A Dodge Pace Arrow motorhome with a 440 big-block purchased for $1,000, and a retired Plymouth Fury from a previous episode.
What ensues over the course of the 40-minute installment is more cuttin', yankin', leakin', stallin', hammerin' and smokin' action than you've seen in a long time, and some techniques that would have made even Cooter wonder, "I'm not sure if we should do that." By the end, though, the payoff is good enough to make you think about perusing AutoTrader for a '68 Charger just to see if maybe...