1970 Dodge Adventurer Pickup Truck Longbed "no Reserve" on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.

Roadkill builds crazy-cheap 1968 Dodge Charger rat rod using an old motorhome

Certain requests for description simply cannot be fulfilled, like if someone asked you to describe Picasso's Guernica or Gilliam's Brazil. There is only one appropriate answer to such entreaties, and that is: "You just gotta see it." That's where we are with the latest episode of Roadkill, wherein Messr's Freiburger and Finnegan dig out a 1968 Dodge Charger that Freiburger acquired in exchange for a set of cylinder heads, and intend to stuff it with the big-block motor from a long-bed, three-quarter ton Dodge pickup.
Only the pickup is too nice to tear apart, and the Charger needs a whole lot more lovin' - and parts - than initially expected. Enter, stage right, the Class A Dodge Pace Arrow motorhome with a 440 big-block purchased for $1,000, and a retired Plymouth Fury from a previous episode.
What ensues over the course of the 40-minute installment is more cuttin', yankin', leakin', stallin', hammerin' and smokin' action than you've seen in a long time, and some techniques that would have made even Cooter wonder, "I'm not sure if we should do that." By the end, though, the payoff is good enough to make you think about perusing AutoTrader for a '68 Charger just to see if maybe...