2006 Dodge Magnum R/t Wagon 4-door 5.7l Hemi V8 Sunroof Only 41k Miles!!! on 2040-cars

Auto blog

Killing the Dart and 200 might lower FCA's fuel economy burden

Killing the Dodge Dart and Chrysler 200 could allow FCA US to take advantage of an intriguing quirk in the next decade's fuel economy regulations. By increasing its ratio of trucks versus cars, the automaker might not need to worry so much about hitting the more stringent efficiency rules. At first thought, it might seem harder for an automaker with a ton of trucks to meet the government's mandated 54.5 mile per gallon corporate average fuel economy for 2025. However, every company doesn't need to hit that lofty figure, according to The Detroit Free Press. The exact target varies by the product mix between trucks and cars. "While passenger car and light truck categories have separate CAFE targets, it's still true that more trucks versus cars in a company lineup means a lower combined CAFE target," Brandon Schoettle, Project Manager Sustainable Worldwide Transportation at the University of Michigan Transportation Research Institute, told Autoblog. "While passenger car and light truck categories have separate CAFE targets, it's still true that more trucks versus cars in a company lineup means a lower combined CAFE target." FCA US' current product blend has 80 percent pickups and CUVs, which means the company stands to benefit from a lower fuel economy target. It might not seem entirely fair environmentally, but this is a great move from a business perspective. The new CAFE rules aren't set in stone, according to The Detroit Free Press, but potentially taking advantage of the regulation is just one more reason to cut the Dart and 200. Modern crossovers also aren't gas guzzlers like older SUVs, which could make it easier to hit the fuel economy target. "Utilities offer practicality and versatility that cars do not, and now, built on car architectures, they do not penalize consumers on fuel economy as they once did," AutoTrader Senior Analyst Michelle Krebs told Autoblog. Schoettle warns that FCA is still making a gamble by killing the small sedans. "Depending on the previous sales volumes and how much these vehicles might have exceeded their specific CAFE targets, it's possible that these cars helped earn CAFE credits for FCA that they could bank for future use," he said. "Future sales breakdowns [car vs.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Our video tribute to Star Wars with a Stormtrooper Charger

When the refreshed Dodge Charger debuted, the white one was immediately compared to a Star Wars Stormtrooper helmet. Chrysler recently ran with that idea and decorated a fleet of cars, including some Chargers, for use in a marketing stunt to hype its wares alongside the no-hype-necessary Episode VII: The Force Awakens film. We got our hands on one for a day and had some fun making a few videos. Above are a few shorts with names that we at least think are funny. There's one that includes the latest example of video producer Chris McGraw's patented nightlapse technology (it's a hyperlapse shot at night, which just looks plain neat). In the clip below, you can see all of the car's various Stormtrooper-inspired details. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. The car started out as a bright white Charger R/T Scat Pack and was treated to a partial vinyl wrap on the body and the glass. The fantastic 485-horsepower Hemi V8 was left alone. Watch the videos and then tell us how they're non-canon in the comments. Humor Dodge Videos Original Video star wars dodge charger scat pack