2005 Magnum R/t Hemi 5.7l * Muredered Out * 22's * Charger * Challenger Srt 6.3 on 2040-cars

Auto blog

2013 Dodge Dart GT

My younger brother bought a Dodge Dart earlier this summer. It's a basic SXT, in Maximum Steel Metallic, with the 2.0-liter engine, a six-speed automatic transmission and not a whole lot else. Unfortunately, at the time, the Dart was one of the few cars in the compact class I'd never driven. I didn't know a lot about it, and therefore, didn't have a lot to say when he bought it. I think the words "based on an Alfa," popped out when I first saw it.
As it turns out, he's grown quite fond of the dark gray sedan, so it was with some degree of enthusiasm that I paid him a visit in this bright-orange Dart GT. I was excited to see what it was about the Dart that he enjoyed so much, despite my tester featuring a different engine, transmission and a lot more tech. After a week with the car, though, I must say: I don't quite see what all the fuss is about.
Driving Notes

Chrysler recalling 67k trucks with manual transmissions

Earlier this month, Chrysler announced the recall of some 280,000 pickup trucks over concerns that their axles could seize up. Now the automaker has announced an entirely separate recall of another 66,819 trucks over the springs that could break in the clutch ignition interlock switch. The recall affects Dodge Ram 1500, 2500 and 3500 pickups, as well as the Dodge Dakota and Mitsubishi Raider. The issue is relevant only to those trucks fitted with manual transmissions, from the 2006 and 2007 model years and manufactured between July 1, 2005, and July 31, 2006. Since a broken spring could, according to statements issued by the National Highway Traffic Safety Administration and FCA US LLC (previously known as the Chrysler Group) prevent the vehicle from starting, or cause it to move unintentionally once the ignition kicks over, the automaker will begin notifying owners of the affected vehicles just before Valentine's Day to bring their trucks into their local dealers to have the clutch ignition interlock switch replaced. FCA emphasizes, however, that the unintended movement would only occur "in rare cases" and only "if recommended starting procedures are not followed." Only one such case is known to have occurred, but it did regrettably result in a fatality. Statement: Clutch Ignition Interlock Switch December 29, 2014 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary global recall of an estimated 66,819 older-model pickup trucks equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. An investigation by FCA US engineers discovered switches in certain model-year 2006 and 2007 pickups may be equipped with spring wire that differs from wire used in previous switches. The alternate wire may break and, as a result, the vehicles may not start. In rare cases, a vehicle may – if recommended starting procedures are not followed – exhibit unintended movement when its ignition key is turned. The Company is aware of one fatality related to this campaign. It stemmed from the single known accident involving this population of vehicles. The recall covers certain Dodge Dakota, Dodge Ram 1500, 2500, 3500 and Mitsubishi Raider pickups. Switches with the alternate wire were not used in any vehicles produced before July of 2005, or after June of 2006. The Dakota and Raider are no longer in production.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat