No Reserve In Az - 2009 Dodge Grand Caravan Se Minivan Sto-n-go Seats Rear A/c on 2040-cars

Auto blog

NHTSA is investigating FCA shifters for roll-away accidents again, this time the rotary units

It seems FCA's shifter troubles aren't over yet. Now, just a few months after issuing a recall to resolve user-related issues with its monostable shifters, the company is again under investigation by NHTSA. The issue is related to the potential for cars to roll away when the rotary-style shifter is not properly placed in park. Two FCA models are the subject of this investigation: the 2013–2016 Ram 1500 and the 2014–2016 Dodge Durango. NHTSA estimates about 1,000,000 vehicles would be affected if a recall is issued. The investigation was started following 43 complaints of vehicles rolling away while supposedly being in "park." Among the complaints were reports of 25 crashes and 9 injuries. NHTSA does point out that in every incident, the parking brake was not engaged. A representative from FCA also gave us an official statement regarding the investigation: "FCA US is cooperating fully with NHTSA's investigation, the scope of which is limited. Other vehicles equipped with rotary shifters are not included. In accordance with prudent practice, the Company joins NHTSA in urging all drivers to use their vehicles' parking brakes." View 35 Photos As mentioned above, other Chrysler products with rotary shifters, such as the Pacifica minivan and 200 sedan, are not involved in this investigation. One of the key differences, as the representative told us, is that these vehicles have electronic parking brakes that automatically engage if the driver does not select park and then opens the door with the seatbelt unbuckled. The Ram 1500 and Durango feature mechanical, manually operated parking brakes and therefore cannot activate the brake automatically. Because this is currently an investigation, an exact cause for the incidents has yet to be determined, and none of the vehicles have been recalled. It's possible there could be a mechanical defect. However, the issue could be a confusing interface causing user error, as was the case with FCA's monostable shifters, where drivers think they've put the car in park but actually haven't. Something that indicates it could be a case of confused users is that NHTSA also opened an investigation into 2012–2014 Jaguar XF and Land Rover Range Rover Evoques for similar issues. Both vehicles use a rotary shifter and have had roll-away complaints levied as well. Even if it is a case of user error, FCA and Jaguar Land Rover may still have to recall their vehicles.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.