2012 Dodge Grand Caravan Power Sliding Doors Sxt - $269 P/mo, $200 Down! on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Jeep Grand Cherokee, Dodge Durango still catching fire after recall

Automakers issue recalls all the time. It's part of the cost of doing business. We just assume that once the recall has been carried out, the problem in question has been fixed. But that's not always the case, as this latest investigation being undertaken by the National Highway Traffic Safety Administration goes to show. The problem stems back to a recall issued by Chrysler last summer. It revolved rather the sun visor in the SUVs it makes at its Jefferson North Assembly Plant – specifically, the screw affixing the sun visor could end up rubbing against the wiring for the lamp in the vanity mirror, potentially causing an electrical short and even a fire. 62 such short circuits, 38 fires and three injuries reported, prompting Chrysler to recall nearly 900,000 units of the 2011-2014 Jeep Grand Cherokee and Dodge Durango (over 650,000 of them in the United States). The plastic spacers they installed to rectify the problem, however, may not have done the trick. Eight reports (but none involving injuries) have been filed with the NHTSA regarding the same issue recurring, spurring the government agency to open a new investigation into the matter. If deemed necessary, the NHTSA could ask FCA to issue another recall to fix the issue again, which we may necessitate the installation of a fuze to prevent any such the electric short. Related Video: INVESTIGATION Subject : Headliner Fires Date Investigation Opened: MAY 01, 2015 Date Investigation Closed: Open NHTSA Action Number: RQ15003 Component(s): ELECTRICAL SYSTEM , INTERIOR LIGHTING Manufacturer: Chrysler (FCA US LLC) SUMMARY: On July 1st, 2014 Chrysler (FCA US LLC) issued safety recall 14V-391 to remedy a wiring-related fire hazard on the headliner of approximately 661,888 model year (MY) 2011-2014 Jeep Grand Cherokee and Dodge Durango vehicles manufactured between January 5, 2010 and December 11, 2013. The recall was in response to the Office of Defects Investigation (ODI) investigation EA14-001 during which data provided by Chrysler indicates that the fire is caused by an electrical short in the vanity lamp wiring for either one of the sun visors mounted on the vehicle. The sun visors are mounted to the roof of the vehicle through the headliner with three metal screws.

Roadkill pits every project car against each other

The guys behind Motor Trend's monthly Roadkill series have collected nine of their favorite project cars from their videos and pitted them against each other in a battle royale to determine a winner. It's 44 minutes long, but it's completely worth the investment of time.
The cars run the gamut from a 1973 Chevrolet Ramp Truck, a 1975 AMC Pacer and a legitimately impressive 1967 Chevy Camaro, and they are pitted against each other to see which is the fastest around an autocross course. The drivers include Roadkill's two hosts and Motor Trend's Johnny Lieberman and Carlos Lago. It's reminiscent of the best episodes of Top Gear and worth a watch.
So it's the weekend - the perfect time to relax. Grab your preferred beverage, get comfortable and enjoy 44 minutes of some seriously ratty but utterly cool project cars as they are throttled within an inch of their lives (or past it). Scroll down to check out the video.