1973 Dodge Dart Swinger 5.2l 2 Door (project Car) on 2040-cars

Auto blog

The Dodge Demon's massive drag tires are just barely street legal

Despite the gaffe that was the Vin Dieselgate leak (no, not that one), Dodge and SRT are soldiering on with the twelve-part Dodge Demon rollout in the lead up to the car's reveal at the New York Auto Show. The Vin Diesel video showed what is almost assuredly the car's front, but now we get an official view of the Demon's rear in this week's video, "Wide Body." Along with the new view, Dodge shows off a cryptic license plate (Michigan #2576@35) and details on the Demon's tantalizing wheel and tire combo. That wheel and tire combo, meant to fill out the Demon's new wide wheel arches, is frankly impressive. Lightweight 18- by 11-inch wheels are wrapped in special Demon branded Nitto NT05R tires measuring an astounding 315/40R18 at all four corners. Not only does that trump the old Camaro Z/28's 305 section tires, it makes the Demon the first production car to come equipped from the factory with drag radials, claims Dodge. Presumably, the goal with the Demon is to provide enough power and grip to rotate the Earth underneath the car rather than propelling the car itself down a dragstrip. Beyond that, few other details were revealed. Dodge provided some vague information about how the "wide-body is laser clearanced, and the entire chassis is e-coated for durability before final assembly," but doesn't actually explain what that really means. We do know now that the flared fenders add 3.5 inches to the Demon's overall width. Overall, the car looks mean and purposeful, especially wrapped in just barely street-legal rubber. Follow along at www.ifyouknowyouknow.com and see if you can find and decipher all the hints. Related Video: Design/Style New York Auto Show Dodge Coupe Performance tires dodge demon dodge hellcat

Chrysler extends fuel tank warranties on LX cars, NHTSA ends probe

The National Highway Traffic Safety Administration has ended its investigation of 153,817, 5.7-liter and 6.1-liter Hemi V8-powered 2006 Chrysler 300, Dodge Charger and Dodge Magnum models after reports of stalling. Chrysler has responded by granting a lifetime warranty on the fuel tanks for these vehicles.
NHTSA received 299 reports of engines stalling while the models were stopped or driving at low speeds, and began an investigation. The government agency found that the control valve shutoff float in the V8s' 19-gallon fuel tank could malfunction if the fuel had too high of an ethanol content. In many cases, the valve would break in the open position, allowing the tank to be overfilled, which would then cause the cars to stall. However, there were no accidents reported, and the vehicles could be restarted immediately.
There will not be a recall on these vehicles because, "the condition represents a low risk to motor vehicle safety and is adequately addressed by Chrysler's extended warranty," NHTSA said to The Detroit News.

Chrysler readying Hellcat V8 with Viper-like power

A monstrous supercharged V8 engine could be in store for Chrysler and SRT products, if recent rumors are to be believed. Allpar is reporting that the forced-induction V8 - Chrysler's first, if this goes down - could make its debut this summer.
The story goes that the Hellcat would be based on a 6.2-liter Hemi engine, rather than on the existing 5.7- or 6.4-liter versions of the company's vaunted mill. In any case, the general consensus is that the motor will have gobs of power. Modest estimates call for between 500 to 570 horsepower, with some outliers predicting a figure as high as 600 hp. That figure would put the output would place the Hellcat awfully close to that of the 640-hp V10 in the SRT Viper, too. Allpar contends that a slightly lower powered version would allow Chrysler to keep costs below that of the more powerful Ford Shelby GT500, which might be a sweet spot.
The Hellcat could debut in a number of SRT products. SRT versions of the Charger, Challenger and 300 are all up for grabs, as is the rumored SRT Barracuda.