2005 Dodge Dakota Slt on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler readying 20 Moparized vehicles for SEMA

The Las Vegas Convention Center has plenty of space for aftermarket companies and automakers to show off their wares, and it looks like Chrysler is taking advantage of the spacious floor plan. At next month's SEMA Show, Chrysler will have a full 20 cars from its six brands decked out with Mopar gear.
As a hint of what is to come, Chrysler released a handful of teaser sketches showing glimpses of modified Jeep Cherokee, Ram 1500, Fiat 500L and Chrysler 300 concept vehicles. The automaker will also use the venue to show off a new line of Jeep Performance Parts offered by the all-new Mopar Off-Road Division. In addition to the images, Chrysler also issued a brief press release - posted below - breaking down some of the "industry-first features" that Mopar has offered in recent years.