2003 Dodge Dakota Custom Spoiler Body Kit Kenwood Audio Low Miles 1 Owner Carfax on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon sheds seats and insulation to drop weight

You've probably already heard that the 2018 Dodge Challenger SRT Demon will be lighter than the Hellcat Challenger – to tune of more than 200 pounds. What you probably don't know is that the Dodge team did it by dropping most of the seats, along with a few other tricks. The Demon loses 113 pounds by making the front passenger seat with its seatbelt (58 pounds) and back seat (55 pounds including restraints and floor mats) optional, which accounts for a large chunk of the weight loss compared to the Hellcat. The Demon also has unique 18-by-11-inch wheels, which are 16 pounds lighter than the Hellcat's, a manual tilt/telescope steering column instead of the powered one, which loses four pounds, and an 18-pound loss thanks to removing 23 noise, vibration, and harshness parts (the Demon will not be a quiet car, to say the least). Another 20 pounds is lost removing the trunk interior trim and spare tire. Still, the Demon gains 17 pounds thanks to the wide fender flares that accommodate the massive drag radials, which also add 3.5 inches to the car's width. For reference, the lightest Hellcat weighs 4,448 pounds with a manual transmission, and the automatic-equipped car comes in at 4,455 pounds. The Demon will be revealed in April before the New York Auto Show, and Dodge will continue to tease its latest satanic muscle couple weekly until then. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

2013-14 Dodge Viper recalled over faulty door handles

The 2013-14 Dodge Viper is getting a voluntary recall affecting 1,762 cars worldwide to replace their door-handle assemblies. Of the affected vehicles, FCA US reports there are 1,451 in the US, 160 in Canada, 17 in Mexico and 59 of them outside of NAFTA. After receiving three reports of doors either not closing or opening while driving a low speeds, FCA US engineers found a new sealant from a supplier didn't provide sufficient moisture protection to the electronic switches for the door latches. If the parts get wet, this can potentially cause a short circuit. The automaker is quite clear that are no reports of accidents of injuries from this problem. As always, the recall repairs will be done at no cost to owners, and FCA US will be getting in touch with customers soon about the problem. Related Video: Statement: Door-handle Assemblies April 9, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 1,762 cars globally to replace their door-handle assemblies. FCA US launched an investigation after the Company received three warranty claims linked to doors that failed to close or opened inadvertently while vehicles were moving at low speed. The Company is unaware of any related injuries or accidents. Engineers determined a sealant, newly adopted by a supplier, provided inconsistent moisture protection to the electronic switches that control the door latches. Switches exposed to moisture may short-circuit. Affected are approximately 1,451 model-year 2013-14 Dodge Viper SRT cars in the U.S.; 160 in Canada; 17 in Mexico and 59 outside the NAFTA region. Affected customers will be notified and advised when they may schedule service, which will be performed at no cost. Customers with questions may call the FCA US Customer Information Center at 1-800-853-1403.

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.