1969 Dodge Coronet Original R/t 440 Custom Restored Beautiful 505hp On Dyno on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Chop the top of your new Dodge Viper for $35,000

We have good news, and we have bad news. First, the good: It's now possible to get a brand-new Dodge Viper roadster, which is nice, considering we're in the dead of summer and many of us like wind-in-the-hair motoring. Now, the bad: This is not a factory option from the automaker, instead coming courtesy of an aftermarket company called Prefix Performance, and that means it's going to cost you some serious coin.
Called Medusa, this drop-top Viper was created without the knowledge or consent of Dodge, but that's probably fine because Prefix works with the automaker already for the final preparation of the American supercar, including paint. According to the company, the current, fifth-gen Viper was built with a convertible version in mind, so no chassis strengthening is required. From the looks of the somewhat grainy photos available, the conversion appears of very high quality.
Want one? Well, that means you're going to need to procure a Viper - Prefix has 10 units ready for transformation as it stands - and that's going to cost at the very least $102,485. Then, you'll need to write a check for an additional $35,000 for Prefix to surgically remove the car's roof. Thing is, for that kind of cash, a prospective owner could buy, among other very nice options, a Viper hardtop and a loaded Miata, or a Corvette Stingray convertible and several pockets full of change. Or, perhaps a new Viper hardtop and a used, first-gen Viper convertible?

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.