1967 Dodge Coronet Rt 440 on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Chrysler investigating complaints of vehicles with faulty power modules

Chrysler owners are hopping mad after experiencing a series of electrical gremlins in some of the company's vehicles. Issues range from mere annoyances - windows rolling down and radios turning off of their own accord - to serious safety issues, with headlights that randomly shut off at night and cars that stall and refuse to start.
The issues are being blamed on the total integrated power module, which can cost up to $1,000 for customers to replace. This, of course, has led to a hefty batch of complaints to the National Highway Traffic Safety Administration, with 240 owners expressing their displeasure so far. Another site, CarComplaints.com, has registered over 300 complaints relating to the 2010 to 2011 Jeep Grand Cherokee and Dodge Durango, alone, according to The New York Times.
Chrysler has acknowledged that it's investigating the complaints and is analyzing the faulty TIPMs, but that isn't quite enough for customers of the affected vehicles. The newspaper has snagged a few of the more harrowing tales with the electrically challenged Chrysler products, culled from the NHTSA complaints.

2016 Dodge Charger Pursuit Vehicle Gets Uconnect 12.1 | Autoblog Minute

Dodge introduces new tech into its 2016 pursuit vehicles that even Jake and Elwood couldn?t outrun. Autoblog's Adam Morath reports on this edition of Autoblog Minute.