1969 Dodge Charger Rt 440 on 2040-cars

Auto blog

Mopar maneuvers into SEMA with a multitude of modified models

As the aftermarket and performance arm of Fiat Chrysler Automobiles, Mopar has a duty to extract everything from the company's models that it can, and there's no better place to show all of its work off than the annual SEMA Show.
Dodge really gets in on the act this year with several customs to show off different parts of the brand's performance heritage. Perhaps the most interesting among them is the track-prepped Viper ACR Concept (pictured above). It wears a custom body kit to produce even more downforce, thanks in no small part to a monstrous wing at the back. To shed weight, most of the interior is stripped out, as well. Next up, the Challenger T/A Concept takes inspiration from '70s Trans-Am racing in a livery of Sublime Green and matte black paint. The center scoop in the hood keeps the 6.4-liter V8 fed with cool air, and the special's 20-by-9.5-inch matte black wheels keep it planted in the corners.
Also getting the once-over from Mopar is the Charger R/T. It wears the division's body kit, and under the hood, a cold-air intake keeps the 5.7-liter V8 breathing. The suspension is retooled to hold the road better with a coil-over kit, upgraded sway bars and strut tower braces for the front and rear. The company is also showing off a snazzy blue Charger with a mean look. The final Dodge getting work from Mopar is the Dart R/T Concept with bright, O-So-Orange paint and a matte black hood with a scoop hooked directly to the air intake. The performance-oriented design is finished off with a coil-over suspension and big brake kit, as well.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

2015 Dodge Viper getting small increase in power

The Viper is used to being the most powerful car in the Dodge and SRT stables, but the arrival of the 2015 Dodge Challenger SRT Hellcat means that's no longer the case. The serpentine supercar is, however, reportedly getting a small boost in output for 2015, amounting to all of five horsepower.
The increase was uncovered by Road & Track courtesy of the SAE J1349 certification process to which Detroit's Big Three automakers submit themselves and which reports the Viper's output at 645 hp instead of the 640 it was rated at until now. There are a hundred factors that could have contributed to the relatively mild boost in output (best guess? nothing at all changed...), but we doubt anyone's going to complain about some extra horses under the hood.
The five-horsepower boost brings the Viper that much closer to the 650-hp Chevy Corvette Z06, not to mention the 707-hp Hellcat, but the Viper's impressive power-to-weight ratio ought to mean it'll have little problem keeping up in a straight line - which is just one of the reasons why Chrysler won't shoe-horn the Hellcat into the Viper: as R&T points out, the supercharged engine is too heavy and the blower makes it too tall to fit in the Viper's engine bay.