2021 Dodge Challenger on 2040-cars

Auto blog

Dodge Charger to slim down and run turbo four in next generation

The current Dodge Charger is getting long in the tooth. It was originally introduced in 2005 as a 2006 model. In car terms, that's an eternity, though it's been refreshed twice. Still, FCA US will keep the LX-generation car going, reportedly facelifting it one last time for 2019. After that, there are some bigger changes in store . Automotive News is reporting that the follower to the current LX Charger will lose almost 500 pounds and will once again offer a turbo four-cylinder. You might remember the front-wheel-drive four-banger Charger of the early '80s. The recharged sedan will be twin-turbo and it's going to use the 300-horsepower four-cylinder engine currently under development for the 2018 Jeep Wrangler, AN says. The target weight for the future car is around 3,500 lbs, while the current car has a curb weight of nearly 4,000 lbs. Look for it to arrive in the early 2020s. The new platform will have a touch of Italian flair instead of the Daimler-Benz flavor embedded deep inside the LX cars. It will be built on an extended version of the 2017 Alfa Romeo Giulia's "Giorgio" platform, according to AN. Dealers were already shown a styling-buck almost a year ago. Related News: Featured Gallery 2015 Dodge Charger R/T View 42 Photos News Source: Automotive NewsImage Credit: AOL Alfa Romeo Dodge Future Vehicles Sedan FCA

South Dakota dealer filled to brim with classic cars

Other than the Sturgis Motorcycle Rally and Mount Rushmore, South Dakota isn't generally a hot topic, but that just means that cool stuff can hide in the open waiting to be discovered. Case in point: the classic car dealer Frankman Motor Company that operates three locations in Sioux Falls, SD.
Unearthed by the folks at Bring a Trailer, Frankman is a treasure trove of vintage, American iron. Their collection is full of the type of vehicles your irresponsible but cool uncle would show up with when you were a kid. Even better, these cars are priced at a level a working man can afford.
If you are lusting about a cruiser then Frankman has a 1956 Cadillac Deville Hard Top Sedan (pictured right) with 82,896 miles for $12,975. It's painted a color called Cascade Grey, but looks more like a pastel purple in pictures. While it needs some repairs to the accessories, the Caddy runs and drives, which is all you really need.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.