1973 Dodge Challenger on 2040-cars

Auto blog

What's the deal with Chrysler demanding colleges crush their Vipers? [w/video]

Students and teachers at a Washington community college are up in arms following an order from Chrysler that it must destroy the pre-production Dodge Viper that was donated to the school's automotive technology program ten years ago.
The Viper in question is said to be the fourth off the production line, based on its VIN, and has had its emissions controls disabled, allowing its ten-cylinder engine to produce 600 horsepower, according to a report from Yahoo! Autos. As one of the first Vipers ever produced, the school's AT instructors claim it could be worth $250,000 in a museum, while a local news report purports that Jay Leno once tried to purchase the car, but the sale was prevented by Chrysler.
As pointed out by our friends at Autobytel, though, there are a lot of things in this story that don't quite add up. Immediately noticeable from the news report embedded below - which shows the car at South Puget Sound Community College - is that the car in question is not a 1992 model. When the Viper went on sale in 1992, it was only available as an RT/10 with a (flimsy) soft top, like the red car shown above. But the car featured in the report from KING5 News (inset image) is clearly a hardtop Viper GTS, which didn't enter production until 1996. And even if, as reported by a local newspaper, the hardtop featured is a prototype, it doesn't explain the lack of another iconic feature of the first Vipers - their distinctive side pipes. This kind of pokes holes in the school's argument that this is the fourth Viper to ever roll down the line. At best, this appears to be a pre-production Viper GTS.

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.