1973 73 Dodge Challenger Original Unmolested Survivor, V-8 Buckets And Console on 2040-cars

Auto blog

Dodge Scat Pack for 5.7L Hemi V8 detailed, priced

Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.