1970 Dodge Challenger R/t 7.2l on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

FCA's large, LX-based RWD cars will stick around until 2020

Fiat Chrysler Automobiles plans to stick with the Dodge Challenger, Dodge Charger, and Chrysler 300 until at least 2020, reports Automotive News. The information comes from two unnamed sources and was loosely confirmed by details in the automaker's new labor contract with Unifor, Canada's auto union. The plan, according to two anonymous sources, is to lightly refresh the Challenger, Charger, and 300 until the vehicles make the switch to FCA's new Giorgio platform. The refresh, as Automotive News points out, will happen in 2018. The Giorgio platform currently underpins the Alfa Romeo Giulia and is expected to find its way to two of the three large American vehicles for the 2021 model year. At that time, FCA will discontinue either the Charger or the 300, claim AN's unnamed sources. If one of the vehicles were to go, it would most likely be the 300. The 300's LX platform would be approximately 15 years old in 2020 and the vehicle doesn't draw in as many sales as the Challenger or the Charger. The Charger made the switch from the LX platform in 2010 with the current model utilizing the mildly updated LD platform, while the Challenger recently moved from the LC platform to the LA platform last year. All of those rear-wheel-drive platforms are closely related. Automotive News points out that FCA CEO Sergio Marchionne stated that the new platform could be utilized across various applications in a conference call with analysts last month. The plan, according to the report, is to stretch and widen the Giorgio platform for the next-gen Challenger and Charger. The new platform is also rigid enough to allow the automaker to add a convertible to its lineup, which could lend further credence to rumors of an upcoming Barracuda. Hopefully, the move to the new Giorgio platform doesn't delay the all-wheel-drive Challenger GT AWD or the wide-body, Hellcat-powered Challenger ADR. We'll just have to wait and see. Related Video: News Source: Automotive News - sub. req. Chrysler Dodge Coupe Performance Sedan FCA fiat chrysler automobiles