2011 Dodge Caliber Loaded Gas Saver! One Owner! 80+ Photos! Look! on 2040-cars

Auto blog

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

NHTSA investigating Ram 1500 models for rear differential failure

The National Highway Traffic Safety Administration is investigating Fiat Chrysler Automobiles and its Ram brand following a number of reports regarding the 2005 Dodge Ram 1500 pickup. According to 15 consumer complaints, the trucks' rear differential locked up while in other cases, the driveshaft separated at its connection to the diff.
Nearly half of the reports claim the truck was traveling at or above 50 miles per hour, while two consumers reported that the diff lockup/driveshaft separation sent their pickups into a spin. Most troubling, though, is that consumers reported little to no sound indicating there was a problem with their truck.
We reached out to Ram for additional information, such as how many vehicles may be affected or what equipment might be fitted that could cause the issue. Unfortunately, the company wasn't willing to elaborate on specifics.