Lux 2.4l Cd Front Wheel Drive Power Steering Abs 4-wheel Disc Brakes Fog Lamps on 2040-cars

Auto blog

Dodge Charger Hellcat makes 1,032 hp with Hennessey help

Sometimes you just want four doors. Earlier this week we brought you Hennessey's riff on the Dodge Challenger Hellcat. Now comes the Charger. Much like its two-door sibling, the Charger gets boosted to as much as 1,032 hp and 987 lb-ft of torque (at the crank) thanks to the addition of a twin-turbocharging setup that works with the factory supercharger. The turbo headers and downpipes are stainless steel, and there is a high-flow air-to-water intercooler and dual-turbo waste gates. Hennessey also beefs up the fuel injectors, fuel pump, and the rest of the fuel system. The engine management system and chassis are recalibrated to accommodate all of this. You also get numbered plaques signed by John Hennessey, the boss of the Texas tuning outfit, and the technician who does your build. Hennessey's additions result in zero-to-60 mph sprints in 2.7 seconds, and the big sedan can run the quarter mile in 9.9 seconds at 142 mph. Like the Challenger, the Charger has the same disclaimer: the lofty horsepower figure comes from an engine dyno, and it will be a 15-to 20-percent lower at the rear wheels. Related Video: Image Credit: Hennessey Performance Dodge Performance Sedan Hennessey dodge charger hellcat

Mopar rolls out new Scat Packages for Dodge Challenger, Charger and Dart

Dodge buyers looking for that extra performance edge, take note: Mopar is bringing back the Scat Pack. Announced at the SEMA Show in Las Vegas today, the new Scat Packages will be available in three stages for the Challenger, Charger and Dart starting next spring.
Upgrades for the Charger and Challenger equipped with the 5.7-liter Hemi V8 engine include a
new cold-air intake and cat-back exhaust, as well as a remapped ECU. Upgrade to the Scat Package 2 and you get a new camshaft, and the Scat Package 3 tosses in ported and polished heads and hi-flow headers. Upgrades for the Dart GT with the smaller 2.4-liter, four-cylinder Tigershark engine with six-speed manual transmission start with a cold-air intake, short-throw shifter and upgraded brakes. The second stage kicks in a remapped ECU and cat-back exhaust, while the Scat Package 3 for the Dart gives you even bigger brakes, an adjustable suspension and sway bars front and rear.

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video: