1998 Dodge Avenger Coupe Rare 5 Speed 2.0l 2-door on 2040-cars

Auto blog

2013-14 Dodge Viper recalled over faulty door handles

The 2013-14 Dodge Viper is getting a voluntary recall affecting 1,762 cars worldwide to replace their door-handle assemblies. Of the affected vehicles, FCA US reports there are 1,451 in the US, 160 in Canada, 17 in Mexico and 59 of them outside of NAFTA. After receiving three reports of doors either not closing or opening while driving a low speeds, FCA US engineers found a new sealant from a supplier didn't provide sufficient moisture protection to the electronic switches for the door latches. If the parts get wet, this can potentially cause a short circuit. The automaker is quite clear that are no reports of accidents of injuries from this problem. As always, the recall repairs will be done at no cost to owners, and FCA US will be getting in touch with customers soon about the problem. Related Video: Statement: Door-handle Assemblies April 9, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 1,762 cars globally to replace their door-handle assemblies. FCA US launched an investigation after the Company received three warranty claims linked to doors that failed to close or opened inadvertently while vehicles were moving at low speed. The Company is unaware of any related injuries or accidents. Engineers determined a sealant, newly adopted by a supplier, provided inconsistent moisture protection to the electronic switches that control the door latches. Switches exposed to moisture may short-circuit. Affected are approximately 1,451 model-year 2013-14 Dodge Viper SRT cars in the U.S.; 160 in Canada; 17 in Mexico and 59 outside the NAFTA region. Affected customers will be notified and advised when they may schedule service, which will be performed at no cost. Customers with questions may call the FCA US Customer Information Center at 1-800-853-1403.

Chop the top of your new Dodge Viper for $35,000

We have good news, and we have bad news. First, the good: It's now possible to get a brand-new Dodge Viper roadster, which is nice, considering we're in the dead of summer and many of us like wind-in-the-hair motoring. Now, the bad: This is not a factory option from the automaker, instead coming courtesy of an aftermarket company called Prefix Performance, and that means it's going to cost you some serious coin.
Called Medusa, this drop-top Viper was created without the knowledge or consent of Dodge, but that's probably fine because Prefix works with the automaker already for the final preparation of the American supercar, including paint. According to the company, the current, fifth-gen Viper was built with a convertible version in mind, so no chassis strengthening is required. From the looks of the somewhat grainy photos available, the conversion appears of very high quality.
Want one? Well, that means you're going to need to procure a Viper - Prefix has 10 units ready for transformation as it stands - and that's going to cost at the very least $102,485. Then, you'll need to write a check for an additional $35,000 for Prefix to surgically remove the car's roof. Thing is, for that kind of cash, a prospective owner could buy, among other very nice options, a Viper hardtop and a loaded Miata, or a Corvette Stingray convertible and several pockets full of change. Or, perhaps a new Viper hardtop and a used, first-gen Viper convertible?

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.