Chrysler 2005 P T Crusier Gt Convertible on 2040-cars

Auto blog

Chrysler IPO to be filed as early as this week

An initial public offering for the Chrysler Group could happen this week, following Sergio Marchionne's comments to Financial Times in London, according to a report from The Detroit News. Fiat, which owns 58.5 percent of Chrysler, has been in a battle with the UAW retiree healthcare trust over its minority stake in the company. While the automotive union recognizes its role as a temporary shareholder, the two couldn't come to an agreement on how the shares should be priced.
As Marchionne explained to FT, a Chrysler IPO allows the market, rather than the two competing sides, to determine the value of the shares. The public offering is a risky move, which could potentially hang one side out to dry - if the shares go high, it's bad news for Fiat, but if they go low, the UAW stands to lose. Regardless of where the stock prices go in an IPO, though, it's a move that's being supported by analysts, who are quick to cite Chrysler's near-constant growth and a product lineup that is getting healthier with each new introduction.

SRT reveals Satin Vapor Edition 300, Charger and Challenger SRT models

With the exception of some notable truck and van introductions, Chrysler brands have tended to use the Chicago Auto Show to bring out new special editions, pimp their aftermarket parts support or indulge in the occasional flight of fancy. That plan is holding true for 2014, as well. Cases in point are these new Satin Vapor Editions of the 2014-model-year Dodge Challenger, Dodge Charger and Chrysler 300 - all from SRT.
The Satin Vapor name may sound like a failed 1970s glam-rock band, or a pseudo-gynecological diagnosis from the Old West, but is, in fact, pretty much a tape-and-trim package for this trio of hi-po Mopars. 300, Challenger and Charger alike come shod with 20-inch aluminum wheels finished in Black Satin Vapor Chrome, and are accented with Satin Black bits aplenty. The 300 gets blacked-out mirrors, spoiler and roof; the Challenger applies it to mirrors and its fuel door; while the Charger has the stuff covering its roof, hood and Super Bee tail graphic.
Interiors of the cars have been mildly updated as well, with all three getting some combination of Nappa leather, ultra-suede and carbon-fiberish finishes.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.