2004 Chrysler Concorde Lx Sedan 4-door 2.7l on 2040-cars

Auto blog

Towing with the 2016 Ram lineup [w/video]

I do not tow things. Ever. Yet I recently found myself at the Fiat Chrysler Automobiles proving grounds in Chelsea, MI, where I'd be testing the hauling capabilities of Ram's current product range. This experience was not only a perfect education for a towing novice like me, but allowed me to tow far more weight than I'd ever consider hauling the real world, and all within the safe confines of the Chelsea Proving Grounds. There was an extremely diverse array of vehicles at my disposal, including Ram's gasoline- and diesel-powered offerings with trucks ranging from the 1500 on up through the 5500 Chassis Cab, as well ProMaster vans. Beyond that, FCA brought out a number of vintage Dodge pickups for me to play with, while also working with Case IH to provide a track-loader I could test. I put together a range of videos covering everything from the classics to the production trucks to the construction equipment. And despite some technical difficulties – you'll notice a distinct lack of in-car videos, with blame going to a corrupted micro SD card – I've assembled ten videos that give an up-close look at Ram's offerings. 2015 Ram ProMaster City Let's start small. The ProMaster City only has a towing capacity of 2,000 pounds. That's a reasonably impressive figure for a van that uses the same powertrain as a Chrysler 200. The 2.4-liter four-cylinder and nine-speed automatic weren't really bothered with the extra weight added by the trailer. Even when accelerating at freeway speeds, the ProMaster City didn't feel out of breath or hampered by its load. That said, the rear of the van was unloaded, which probably wouldn't be the case for most consumers. It's unclear how the City would feel if its driver were taking advantage of the max payload (1,883 pounds) and towing. 2015 Ram ProMaster 1500 To be polite, the Ram ProMaster is a difficult vehicle to like. Its awkward seating position is bus-like and lacks the visibility enjoyed by the Ford Transit or the utter driving comfort of the Mercedes-Benz Sprinter. Its 3.0-liter, four-cylinder turbodiesel engine, meanwhile, is something of an anomaly. While it's potent for a four-cylinder diesel, producing 295 pound-feet of torque and 174 horsepower, those numbers don't feel all that impressive when loaded down. The model I tested was barely using half of its 5,100-pound maximum towing weight and was loaded down with just 500 of its 3,620-pound payload. Yet it lacked the pluckiness of the smaller City.

Dodge Challenger spied exercising supercharged Hellcat Hemi V8

One of the prime complaints against the Dodge Challenger is that, even in SRT8 guise, its 470 horsepower is responsible for hauling over 4,200 pounds of vehicle. For comparison, the 420 hp in the Ford Mustang GT only has to deal with 3,618 lbs. Things only get worse from there, as the higher-performance variants of both the Mustang and the Chevrolet Camaro are far more powerful than an SRT8 without adding on much heft.
So what is Chrysler to do? The correct answer is add a whole lot more grunt to its hefty two-door and even the odds. That's where the all-new Hellcat engine comes into play. We reported on this engine in May, and suggested that the Hellcat, a supercharged powerplant based on a 6.4-liter V8, would easily generate 500 to 570 hp and could likely arrive boasting more than 600 ponies.
Chrysler's ace in its sleeve has now been spied testing, with a number of Hellcat-equipped Challengers running the potent new engine both in more urbanized areas and under the sun of Death Valley. The hoods on these testers have been raised to accommodate the engine, and that camouflage over the fascias of these prototypes is there to hide a larger air intake. We also note what appears to be a new split grille under wraps. As for power output, our spies are now suggesting a Viper-equalling 640 hp from the Hellcat-equipped cars.

Fiat talking with banks about buying rest of Chrysler

All that stands in the way of Fiat's total ownership of Chrysler is a 41.5-percent stake currently held by the United Auto Workers healthcare trust, but according to SFGate.com, Sergio Marchionne is currently trying to raise the capital to complete the acquisition. The article says that a deal could be completed in as soon as 12 months, and the estimate for the remaining stake could cost Fiat SpA around $2.98 billion.
With a goal of completing the deal by the end of 2014, Marchionne is said to be in talks with various banks to help finance some of the deal. According to the report, the banks have indicated a need for a stronger balance sheet, controlled debt and reserve cash.
Two things that don't seem to be on the table to get the deal completed include issuing new shares to raise the capital or selling a stake in Ferrari. Fiat started with a 20 percent share of Chrysler in June 2009, and it raised its stake up to 58.5 percent in January 2012.